Docomo SH-10C, Инструкция по эксплуатации

Страница: 160 / 169

41
Manual for PC Connection_DV85.fm
*1 Stored in FOMA terminal’s memory using AT&W commands.
*2 Not stored in FOMA terminal’s memory using AT&W commands. Not reset with AT&F or ATZ commands.
*3 Perform Redial with ATDN
o
or ATDL
o
.
*4 If the ATZ command is executed before the AT&W command is used, terminal settings return to last written
memory, and prior changes are erased.
*5 Settings written into the FOMA terminal’s memory using the AT&W command is stored as non-volatile data
when power is turned off.
ATS5=<n> Sets the backspace (BS)
character. When detected while entering an AT
command, the last character in the input
buffer is deleted. The settings cannot be
changed (default setting: n=8). ATS5=8
o
OK
ATS5?
o
008
OK
ATS6=<n> Sets pause time (seconds) until
dialing. Sets a register, but has no other effect.
n : 2 to 10 (default setting: n=5) ATS6=10
o
OK
ATS8=<n> Sets pause time (seconds) until
comma dialing. Sets a register but does not affect the pause
time (3 seconds).
n=0 : Does not pause
n : 1 to 255 (default setting: n=3) ATS8=3
o
OK
ATS10=<n> Sets the delay time (seconds) for
automatic disconnection
(1/10 seconds).
*1
Sets a register, but has no other effect.
n : 1 to 255 (default setting: n=1) ATS10=1
o
OK
ATS30=<n> Disconnects when no data is sent/
received for at least this amount of
time. Only valid during 64K data communication.
<n> is set in minutes.
n : 0 to 255 (default setting: n=0)
n=0 sets inactive timer off. ATS30=3
o
OK
ATS103=<n> Sets delimiter used when adding
an incoming sub-address to
number dialed. Only valid during 64K data communication.
n=0 :
* Asterisk
n=1 : /Slash (default setting)
n=2 : ¥Yen mark or backslash
ATS103=0
o
OK
ATS104=<n> Sets delimiter used when adding
an outgoing sub-address to
number dialed. Only valid during 64K data communication.
n=0 : #Pound sign
n=1 : %Percent symbol (default setting)
n=2 : &Ampersand ATS104=0
o
OK
AT¥S Displays current command and
S register settings.
*2
―
AT¥S
o
E1 Q0 V1 X4
&C1 &D2 &S0
&E1 ¥V0
S000=000
S002=043
S003=013
S004=010
S005=008
S006=005
S007=060
S008=003
S010=001
S030=000
S103=001
S104=001
OK
AT¥V<n> Selects response code type used
during connection.
*1
Only valid when the ATX<n> command
(
n
P. 40) setting is not n=0.
n=0 : Does not use extended result codes
(default setting)
n=1 : Uses extended result codes
AT¥V1
o
OK
AT command Overview Parameter/Explanation
Execution
example
[M]
[M]
[M]
[M]
[M]
[M]
[M]
[M]
[M]
Manual for PC Connection_DV85.fm 41 ページ ２０１１年５月９日 月曜日 午前１１時５９分