38
AT&D<n>
*1
Set the operation performed when circuit ER (DTR) signal received from DTE is switched
from ON to OFF while online data mode takes effect.
n=0 : Ignore status (status is always considered to be ON)
n=1 : Move to online command mode when status changes from ON to OFF
n=2 : Disconnect line and move to offline mode when status changes from ON to OFF
(default)
AT&D2
OK
AT&E<n>
*1
Set the speed display used when connection is made.
n=0 : Display communication speed of wireless zone
n=1 : Display communication speed between a PC and FOMA terminal (default)
AT&E1
OK
AT&F
Reset the current setting to the default.
When this command is executed during communication, the terminal is reset after the line
is disconnected (displaying "NO CARRIER").
AT&F
OK (When in offline mode)
AT&S<n>
*1
Set control of the data set ready (DR) signal to be output to DTE.
n=0 : Always ON (default)
n=1 : ON at time of connection
AT&S0
OK
AT&W
Register the current settings in FOMA terminal.
AT&W
OK
AT
＊
DANTE
Indicate FOMA terminal reception level in the "
＊
DANTE : <n>" format.
n=0 : Out of service area
n=1 : Received signal level of FOMA terminal is 0 or 1 antenna.
n=2 : Received signal level of FOMA terminal is 2 antennas.
n=3 : Received signal level of FOMA terminal is 3 antennas.
AT
＊
DANTE=? : Display a list of displayable values
AT
＊
DANTE
＊
DANTE : 3
OK
AT
＊
DGANSM=<n>
*2
Set to reject or permit incoming packet communications.
n=0 : Reject setting = OFF, Accept setting = OFF (default)
n=1 : Reject setting=ON
n=2 : Accept setting=ON
AT
＊
DGANSM? : Display current settings
AT
＊
DGANSM=? : Display a list of assignable values
AT
＊
DGANSM=0
OK
AT
＊
DGAPL=<n> [,<cid>]
*2
Set the dialup connections (APN) to permit incoming packet communications. APN uses
<cid> defined by +CGDCONT command.
n=0 : Add to list of APN permitted for incoming communications
n=1 : Delete from list of APN permitted for incoming communications
If the <cid> is not defined by the +CGDCONT command, it can still be added to/deleted from
the list.
If the <cid> is omitted, all the <cid> are added to/deleted from the list.
AT
＊
DGAPL? : Display current settings
AT
＊
DGAPL=? : Display a list of assignable values
AT
＊
DGAPL=0,1
OK
AT
＊
DGARL=<n> [,<cid>]
*2
Set the dialup connections (APN) to refuse incoming packet communications. APN uses
<cid> defined by +CGDCONT command.
n=0 : Add to list of APN rejected for incoming communications
n=1 : Delete from list of APN rejected for incoming communications
If the <cid> is not defined by the +CGDCONT command, it can still be added to/deleted from
the list.
If the <cid> is omitted, all the <cid> are added to/deleted from the list.
AT
＊
DGARL? : Display current settings
AT
＊
DGARL=? : Display a list of assignable values
AT
＊
DGARL=0,1
OK
AT
＊
DGPIR=<n>
*2
Set Caller ID notification when packet communication connection is being performed. This
command is available when a communication is sent or received.
n=0 : Connect to APN directly (default)
n=1 : Connect to APN prefixing 184
n=2 : Connect to APN prefixing 186
When Show/Hide caller ID is specified by dialup network
→
P23
AT
＊
DGPIR? : Display current settings
AT
＊
DGPIR=? : Display a list of assignable values
AT
＊
DGPIR=0
OK
AT
＊
DRPW
Indicate an index for the reception power of the radio waves that FOMA terminal receive.
AT
＊
DRPW=? : Display a list of displayable values
AT
＊
DRPW
＊
DRPW : 0
OK
Upper slot : Command
Lower slot : Example
Description
Содержание F-04B
Страница 1: ...INSTRUCTION MANUAL 10 3 F 04B...
