manualshive.com logo in svg

DMG Pitagora 4.0, Руководство пользователя

Поделиться
Скачать
DMG Pitagora 4.0 Скачать руководство пользователя страница 65

N.

Fault

Type

Description

Remedy

41 Fault ISO

Problem detected in the operation
monitoring of safety module for advanced
door opening / re-leveling. If activated,
the installation goes into “out of service”
mode at the top floor (electric) or bottom
floor (hydro). 

Cod 100: fail on Safety module monitor
during travel 
Cod 200: fail on Safety module monitor at
level

Check the alignment of ISO1 and
ISO2. 
Reset ISO in the menu Faults (§ 5.3).

42

TOC
Communication

No serial link between controller and car
(in case of car serial link system
configuration)

Check CAN link between controller
and top of car board

43 Inspection

The system is in Inspection mode
(NORM/ISP switch set to Inspection) 

EN 81.1/2 
Cod 1: REV input open (STD Version) 
Cod 2: TOC’s REV1 input open 
Cod 3: REV + TOC’s REV1 input open 
Cod 5: REV input open (Pitagora version) 
Cod 6: REV1 input open 
Cod 7: REV + TOC’s REV1 input open 

EN 81.20 
Cod 11: PME inspection (REV) 
Cod 12: TOC inspection (REV1)  
Cod 13: PME + TOC inspection (REV +
REV1) 
Cod 14: PIT Inspection (REV2) 
Cod 15: PME + PIT Inspection (REV +
REV2) 
Cod 16: TOC + PIT Inspection (REV1 +
REV2) 
Cod 17: PME + TOC + PIT Inspection
(REV + REV1 + REV2)

To exit the inspection mode move the
NORM/ISP switch to Normal and
close the safety chain to trigger the
reset procedure

44

Re-levelling not
completed

Hydraulic lifts: the re-levelling procedure
was not completed within 10 seconds. All
subsequent re-levelling requests at the
same floor are inhibited

Check: 
1- the correct operation of the Safety
module and of its sensors ZP1 and
ZP2; 
2- Check the FAI/FAS or ENCODER
sensors and the ZP sensor; 
3- position of the magnets in the re-
levelling zone; 
4- RISO relay.

45 Fault ZP

Door zone contact stays open when the
sensor is in door zone position

Check the correct operation of the
door zone sensor (if present); 
See Fault # 33

Содержание Pitagora 4.0
























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды