manualshive.com logo in svg

DMG Pitagora 4.0, Руководство пользователя

Поделиться
Скачать
DMG Pitagora 4.0 Скачать руководство пользователя страница 33

“Signalisation” Menu

----->>>>>

----->>>>>

OR

----->>>>>

----->>>>>

Floor 0 - 12:30:56 
< Signals >

Parameter

Description

Navigation

Values

Default
Value

Select door
B at floor

Configuration of door A for each floor: set access
to each floor and open or close door parking at
floor (for automatic doors)

◄► (Selection) 
▲▼ (Change floor)

No;  
Pkg. Door
close;  
Pkg. Door
open 

Pkg. Door
close

Door B
Open/Close
time

Door B without limit switch: door opening/closing
time

▲▼
(Increase/Decrease)

1 s <-> 60 s

10 s

Door B
start delay

Door B manual: time before start

▲▼
(Increase/Decrease)

0,1 s <-> 9,9
s

2,0 s

Slipping
Door B

Door B with limit switch: time before slipping fault

▲▼
(Increase/Decrease)

1 s <-> 60 s

10 s

Door B
powered

Door B powered during the run. Not considered
for manual or independent doors

◄► (Selection)

No 
Yes 
Yes AT40

No

Advanced
opening

Parameter for door advanced opening (opening
starts before car stop).

◄► (Selection)

No;  
Yes

No

Photocell
Type

Parameter to select the type of photocell:
NO photocell: contact opens if the beam is free.
The contact closes if the beam is interrupted. The
shock, photocell and open door contacts must be
wired in parallel. 
NC photocell: opposite of the NO photocell. The
shock, photocell and open door contacts must be
wired in series. 
NOTE: The shock, photocell and open door
contacts must all be of the same kind (NO or NC)

◄► (Selection)

NO;  
NC

No

Table of Parameters:

 

Parameter

Description

Navigation

Values

Default
Value

Table of Parameters

Содержание Pitagora 4.0
























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды