manualshive.com logo in svg

DMG Pitagora 4.0, Руководство пользователя

Поделиться
Скачать
DMG Pitagora 4.0 Скачать руководство пользователя страница 4

VVVF parameters and diagnostics handling (only FUJI FRENIC LIFT LM2)

Advanced control of VVVF with speed, comfort and precision stop control

Software upgrading via USB Device

RS232 serial line for PC and GPRS modem connection

Compatibility with all DMG products

Compatibility with all the +A3 solutions for electrical and hydraulic systems

Protection of shaft access (Unauthorized Shaft Access)

Specifications and descriptions of inputs and outputs

The 4.0 Mother Board contains hardware and software that allows control of the elevator and all its peripherals. Through
the integrated and/or remote programming modules it allows access to all available features. Inputs and outputs are
connected to all electronic and electromechanical devices in the controller and in the lift.

Integrated Programming Module

The Mother Board has a removable programming module that allows viewing and editing of all the basic parameters for the
control panel management and configuration. In VVVF’s version, also FUJI’s parameters of the basic (menu VVVF BASE)
and advanced (VVVF ADVANCED menu) configuration may be viewed and edited.

For details of the programming module operation and an extensive management system menu, see paragraph 

changing

system parameters

.

Remote programming module

An alternative way to access the configuration menu of the controller, in the view/modification mode, is by connecting the
removable keypad of the DMG V3 Playboard (PlayPad), to the connector PLP V3, mounted on the Lift Control Board.

This module can be connected in various ways:

Connected directly

Connected by a dedicated extension cable directly on the board (in the engine room)

Connected to the board on the elevator car roof (TOC) in the case of lifts with DMG pre-wired serial devices.

Fusion APP

An alternative way to access the controller is based on Fusion App.

Содержание Pitagora 4.0
























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды