manualshive.com logo in svg

DMG Pitagora 4.0, Руководство пользователя

Поделиться
Скачать
DMG Pitagora 4.0 Скачать руководство пользователя страница 32

Parameter

Description

Navigation

Values

Default
Value

Closing
time with
calls

Time (in sec.) before door closes in case of
registered calls

▲▼
(Increase/Decrease)

1 s <-> 60 s

2 s

Doors Nb.

Number and type of doors

◄► (Selection)

-1 door 
-2 doors
simult. 
-2 doors sel. 
-2 doors
sel+through

1 access

Type Door
A

Selection of door type for entrance A: 
1) Manual / Not present: manual doors at floors,
elevator car doors manual or not present; 
2) Car independent: manual doors at floors,
elevator car doors independent; 
3) Car automatic: manual doors at floors, elevator
car doors automatic;
4) Combined auto: automatic doors in the
elevator car and at floors

◄► (Selection)

Manual / not
present; 
Car
Independent;
Car
automatic;  
Combined
Auto 

Combined
Auto

Door A with
limit switch

Presence of a limit switch for door A (not present
for manual and independent doors)

◄► (Selection)

No;  
Yes

No

Select door
A at floor

Configuration of door A for each floor: set access
to each floor and open or close door parking at
floor (for automatic doors)

◄► (Selection) 
▲▼ (Change floor)

No;  
Pkg. Door
close;  
Pkg. Door
open 

Pkg. Door
close;

Door A
Open/Close
time

Door A without limit switch: door opening/closing
time

▲▼
(Increase/Decrease)

1 s <-> 60 s

10 s

Door A
start delay

Door A manual: time before start

▲▼
(Increase/Decrease)

0,1 s <-> 9,9
s

2,0 s

Slipping
Door A

Door A with limit switch: time before slipping fault

▲▼
(Increase/Decrease)

1 s <-> 60 s

10 s

Door A
powered

Door A powered during the run. Not considered
for manual or independent doors

◄► (Selection)

No 
Yes 
Yes AT40

No

Type Door
B

Selection of door type for entrance B (see Type
Door A):

◄► (Selection)

Manual / not
present; 
Car
Independent;
Car
automatic;  
Combined
Auto

Combined
Auto

Door B with
limit switch

Presence of a limit switch for door A (not present
for manual and independent doors)

◄► (Selection)

No;  
Yes

No

Содержание Pitagora 4.0
























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды