manualshive.com logo in svg

Dixie Chopper Pursuit 1832S, Руководство по безопасности, эксплуатации и техническому обслуживанию

Поделиться
Скачать
Dixie Chopper Pursuit 1832S Скачать руководство пользователя страница 7

5

700493

SAFETY

3

•  The fuel nozzle must touch the rim of the fuel tank when you add fuel to the mower. Do not use a device to lock the 

fuel nozzle in the open position.

• 

Do not over fill the fuel tank. Leave at least 1 inch (25 mm) below the filler neck.

•  Always tighten the fuel tank cap and container cap after you add fuel.
• 

If the fuel spills on your clothing, change your clothing immediately.

3.1.5 MAINTENANCE AND STORAGE

• 

Before you clean, adjust or repair this equipment, stop the engine and disconnect the spark plug wire. Keep the wire 
away from the plug to prevent the engine to start. Disconnect the negative battery cable.

•  Make sure the mower is parked on a solid and level surface.
• 

Never work on a mower that is lifted only by the jack. Always use the jack stands.

• 

Never allow persons to service the mower or its attachments without correct instructions.

•  When you put the mower on a trailer or put the mower in storage, close the fuel valve. Do not keep fuel near flames 

or drain the fuel inside a building.

• 

Disconnect the battery before you service the mower. Always disconnect the negative battery cable before the 
positive battery cable. Always connect the positive battery cable before the negative battery cable.

•  Charge the battery in an area with good airflow. The battery can release hydrogen gas that is explosive. To prevent an 

explosion, keep any device that can cause sparks or flames away from the battery.

• 

Disconnect the battery charger from the power supply before you connect or disconnect the battery charger to the 
battery. Wear protective clothing and use insulated tools when you service the battery.

• 

Be careful and wear gloves when you check or service the cutting unit blades. Replace any damaged blades, do

• 

not try to correct a damaged blade.

•  Keep your hands and feet away from parts that move. Do not adjust the mower with the engine in operation, unless 

the adjustment needs the engine in operation.

•  Carefully release the pressure from components with stored energy.
•  Keep the mower and the engine clean.
•  Allow the engine to become cool before storage and always remove the ignition key.
•  Keep all nuts, bolts and screws tight to make sure the equipment is in safe condition.
•  Replace worn or damaged parts for safety. Replace damaged or worn decals. Only use parts, accessories and 

attachments approved by Dixie Chopper.

•  To decrease the fire hazard, remove materials that burn from the engine, muffler, battery tray and fuel tank area.
• 

Disconnect the battery and controller connectors before you weld on this mower.

3.1.6 WHEN YOU PUT THE MOWER ON A TRAILER

• 

Be careful when you load or unload the mower on a trailer. Trailer must be wider than the mower and can carry the 
weight of the mower.

•  Use a full-width ramp to load or unload the mower on a trailer.
•  Use straps, chains, cables or ropes to fasten the mower to the trailer. Both front and rear straps must be sent down 

and toward sides of trailer.

•  Make sure that all latches are correctly fastened.

Содержание Pursuit 1832S





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды