Dixie Chopper Pursuit 1832S Скачать руководство пользователя | Manualshive

Страница: 34 / 52

background image

32

700493

9.7 CHARGE THE BATTERY

Read the battery charger manual for specified instructions on the operation of the charger.

When possible, remove the battery from the mower before you charge the battery. If the battery is not sealed, check and
make sure the level of the electrolyte is above the plates in all of the cells.

Make sure the battery charger is turned OFF, then connect the battery charger to the battery terminals as specified in the
battery charger manual.

Always turn OFF the battery charger before you disconnect the battery charger from the battery terminals.

9.8 ENGINE EXHAUST

If you sense a change in the color or sound of the exhaust, stop the engine immediately. Identify the problem and have
the system repaired.

Torque all exhaust manifold hardware equally. Tighten or replace the exhaust clamps.

MAINTENANCE

9

WARNING

Charge the battery in an area with good airflow. The battery can release hydrogen gas that is explosive. To prevent an
explosion, keep any device that can cause sparks or flames away from the battery.

When the battery charger is turned on, to prevent injury, stay away from the battery. A battery that is damaged can
cause an explosion.

WARNING

The exhaust fumes contain carbon monoxide. The carbon monoxide in the exhaust fumes can increase to dangerous
levels. To protect you from carbon monoxide poisoning, inspect the complete exhaust system every month and replace
damaged components immediately.

NEVER operate the engine without enough ventilation.

The temperature of the exhaust components can be greater than 300° F (149° C). To prevent the burns, do not touch a
hot exhaust system.

«
...
32
33
34
35
36
...
»

Содержание Pursuit 1832S





















































Отзывы:

Нет отзывов

Похожие инструкции для Pursuit 1832S

32in Recycler 30118

Бренд: Toro Страницы: 4

Бренд: Ariens Страницы: 32

Бренд: Bad Boy Страницы: 20

Бренд: Parker Страницы: 25

Бренд: Yard-Man Страницы: 4

Бренд: Toro Страницы: 72

Zero Turn Radius Mower

Бренд: Country Clipper Страницы: 25

Бренд: Alamo Industrial Страницы: 186

Бренд: Fieldmann Страницы: 106

Commercial Front Cut Rider YHRLD211

Бренд: Yazoo Страницы: 26

Бренд: RHINO Страницы: 23

Бренд: Snapper Страницы: 44

Бренд: Bad Boy Страницы: 36

DR WHISPER LITE

Бренд: Country Home Products Страницы: 38

Бренд: Tiger Страницы: 230

Бренд: Electrolux Страницы: 20

Бренд: Electrolux Страницы: 6

Rear Blades RB 15

Бренд: Land Pride Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды