Dixie Chopper Pursuit 1832S Скачать руководство пользователя

Страница: 48 / 52

700493

QUALITY OF CUT

12.5 STRAGGLERS

Stragglers are separated blades of grass the are not cut,
or are cut incorrectly.

Probable Cause

Remedy

Edge of the cutting blade(s) are not sharp.

Sharpen the blade(s).

See 9.13

Cut (ground) speed is higher than normal

Reduce the cut (ground) speed.

The grass is higher than the level at which the mower can cut
correctly.

Cut the grass more frequently.

Cut in the same direction.

Change the direction of cut more frequently.

The blade speed is too slow

Operate the mower with the engine at full throttle. Inspect the
cutting unit belt.

12.6 STREAKS

A streak is a line of grass that is not cut. The cause of a streak can be a damaged
blade.

Probable Cause

Remedy

Edge of the cutting blade(s) are not sharp.

Sharpen the blade(s).

See 9.13

Cut (ground) speed is higher than normal

Reduce the cut (ground) speed.

The grass is higher than the level at which the mower can cut
correctly.

Cut the grass more frequently.

Cut in the same direction.

Change the direction of cut more frequently.

The blade speed is too slow

Operate the mower with the engine at full throttle. Inspect the
cutting unit belt.

12 QUALITY OF CUT

en-55

12.5 STRAGGLERS ____________________________________________________________

NOTE: Arrow indicates direction of travel.

Stragglers are separated blades of grass the are not cut,
or are cut incorrectly.

Probable Cause

Remedy

Edge of the cutting blade(s) are not sharp.

Sharpen the blade(s).

See 9.13

Cut (ground) speed is higher than normal

Reduce the cut (ground) speed.

The grass is higher than the level at which the mower
can cut correctly.

Cut the grass more frequently.

Cut in the same direction.

Change the direction of cut more frequently.

The blade speed is too slow

Operate the mower with the engine at full throttle. Inspect
the cutting unit belt.

TN0223

QUALITY OF CUT 12

en-56

12.6 STREAKS ________________________________________________________________

NOTE: Arrow indicates direction of travel.

A streak is a line of grass that is not cut. The cause of a
streak can be a damaged blade.

Probable Cause

Remedy

Damaged blade(s).

Replace the blade(s).

See 9.12

The tires compresses the grass before the grass is cut.

Check and adjust the tire inflation pressure.

The blades are not installed correctly.

Check to make sure the correct blade is installed on each
motor.

The mower compresses the wet grass before the grass
is cut.

Cut the grass when grass is dry.

TN0224

Содержание Pursuit 1832S





















































Результаты поиска

Содержание Pursuit 1832S

Отзывы:

Похожие инструкции для Pursuit 1832S

Бренды по названию

Популярные бренды

Dixie Chopper Pursuit 1832S, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Pursuit 1832S

Отзывы:

Похожие инструкции для Pursuit 1832S

Бренды по названию

Популярные бренды