Dixie Chopper Pursuit 1832S Скачать руководство пользователя | Manualshive

Страница: 12 / 52

background image

10

700493

4.3 MOWER SPECIFICATION

Battery: 12V, 300 CCA

Service Brake: Dynamic braking through the traction circuit

Parking Brake: Integrated in transmission

Fuel Tank: 5 U.S. Gallons (18.9 l)

Traction Drive: Pursuit 1332S / 1836S - Belt driven single hydrostatic drive

Pursuit 1836D / 1844D - Belt driven dual hydrostatic Hydro-Gear® EZT.

Cutting Unit Drive: Belt drive

Ground Speed: Pursuit 1832S / 1836S: 0-6 mph

Pursuit 1836D / 1844D: 0-6 mph

Reverse Speed: Pursuit 1832S /1836S: 0-6.5 mph

Pursuit 1836D / 1844D: 0-3 mph

Pursuit 1832S Cutting Performance: Up to 1.8 acres/hr. @ 6 mph
Pursuit 1836S Cutting Performance: Up to 2.18 acres/hr. @ 6 mph

Pursuit 1836D Cutting Performance: Up to 2.54 acres/hr. @ 7 mph
Pursuit 1844D Cutting Performance: Up to 3.1 acres/hr. @ 7 mph

4.4 CUTTING UNIT SPECIFICATION

1832S

1836S / 1836D

1844D

Blade Length

16.25 inch

13.75 inch (34.9 cm)

15.125 inch (38.4 cm)

Number of blades

2

3

Height of cut adjustment

Six 1/2 inch spacers placed above or below the front wheel mount

and three position rear deck plate.

Blade Tip Speed

@ 3600 rpm engine speed

327 feet/second

315 feet/second

310 feet/second

4.5 BELT SPECIFICATION

Pursuit 1832S / 1836S Traction Belt: 4L-Section, Wrapped, Belt
Pursuit 1836D / Pursuit 1844D Traction Belt: 4L-Section, Wrapped Belt
Pursuit 1832S Engine to Deck Belt: 5L-Section, Wrapped Belt
Pursuit 1836S Engine to Deck Belt: 5L-Section, Wrapped Belt
Pursuit 1836D Engine to Deck Belt: 5L-Section, Wrapped Belt
Pursuit 1844D Engine to Deck Belt: 5L-Section Wrapped Belt
Pursuit 1836S / Pursuit 1836D Deck Belt: HA-Section, Wrapped Belt
Pursuit 1844D Deck Belt: HA-Section Wrapped Belt

SPECIFICATIONS

4

«
...
10
11
12
13
14
...
»

Содержание Pursuit 1832S





















































Отзывы:

Нет отзывов

Похожие инструкции для Pursuit 1832S

Бренд: Yard-Man Страницы: 36

Бренд: MacDon Страницы: 2

Бренд: Snapper Страницы: 25

Бренд: Toro Страницы: 52

Бренд: Cub Cadet Commercial Страницы: 32

Бренд: Jacobsen Страницы: 98

LazerCut LCS405

Бренд: SANLI Страницы: 19

Бренд: Skil Страницы: 106

Бренд: Flymo Страницы: 10

Бренд: Meec tools Страницы: 24

Бренд: Ransomes Страницы: 100

Бренд: Deutz-Allis Страницы: 36

Бренд: White Outdoor Страницы: 36

Бренд: Ryobi Страницы: 13

Бренд: Ryobi Страницы: 48

Бренд: Ryobi Страницы: 24

Бренд: Ryobi Страницы: 25

Бренд: Ryobi Страницы: 348

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды