Dixie Chopper Pursuit 1832S Скачать руководство пользователя | Manualshive

Страница: 33 / 52

background image

31

700493

9.6 BATTERY

Before you service the battery, make sure the ignition switch is in the OFF position and the key is removed.

Tighten the battery cables on the battery terminals, To prevent corrosion, apply a layer of silicone dielectric grease to
battery terminals and ends of cables. Keep the vent caps and battery terminal covers in position.

Before you do any welding operation on the mower, always disconnect the battery cables from the battery and the
connectors from the controllers.

Confirm the battery polarity before you connect or you disconnect the battery cables.

When you install the battery, always connect the positive (RED) battery cable before the negative (BLACK) battery cable.

When you remove the battery, always disconnect the negative (BLACK) battery cable before the positive (RED) battery
cable.

Jump-Starting the Mower

A. Before you try to jump-start the mower, check the condition of the drained battery.
B. Connect the positive (+) battery terminal of the charged battery to positive battery terminal of the drained

battery.

C. Connect the negative (–) battery terminal of the charged battery to frame of vehicle with the drained battery.

D. When the cables are connected, start the engine on the vehicle with the good battery, then start the mower.

MAINTENANCE

9

WARNING

The battery contains corrosive acid. Prevent contact with the battery acid.

Always wash your hands after you service a battery.

WARNING

The battery posts, battery terminals and related accessories contain lead and lead compounds, chemicals known to the
State of California to cause cancer and other reproductive harm.

WARNING

The battery can release hydrogen gas that is explosive. To decrease the risk of an explosion, prevent sparks near the
battery. Always connect the negative jumper cable to the frame of the mower with the drained battery.

CAUTION

When you service the battery, always use the tools with insulation, wear protective glasses and protective clothing.
Discard used batteries as shown in your local regulations.

«
...
31
32
33
34
35
...
»

Содержание Pursuit 1832S





















































Отзывы:

Нет отзывов

Похожие инструкции для Pursuit 1832S

Бренд: Walker Страницы: 100

Бренд: Cadet Страницы: 40

Бренд: Snapper Страницы: 2

Бренд: Wizard Страницы: 48

Бренд: Ferris Страницы: 48

Model Series 420

Бренд: Yard-Man Страницы: 16

Бренд: Gravely Страницы: 54

Бренд: Harrier Страницы: 34

TimeCutter Z17-42

Бренд: Toro Страницы: 44

Бренд: O-Mac Страницы: 64

Бренд: SaMASZ Страницы: 35

Vision Compact 350 Plus

Бренд: Flymo Страницы: 9

Бренд: Flymo Страницы: 4

SimpliStore 300 Li

Бренд: Flymo Страницы: 10

Бренд: Flymo Страницы: 12

Бренд: Flymo Страницы: 13

Бренд: Flymo Страницы: 52

73547 Wheel Horse 520Lxi

Бренд: Toro Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды