manualshive.com logo in svg

Dixie Chopper Pursuit 1832S, Руководство по безопасности, эксплуатации и техническому обслуживанию

Поделиться
Скачать
Dixie Chopper Pursuit 1832S Скачать руководство пользователя страница 13

11

700493

4.6 RECOMMENDED LUBRICANTS

Engine Oil:
API Classification grades SF, SG, SH, SJ or higher

Drive Axle Fluid:

The drive axle fluid is SAE 20W50 API Classification SL.

Grease:

NLGI Grade 2-EP Lithium Complex Grease containing Molybdenum Disulfide.

4.7 SLOPES

DO NOT USE ON SLOPES GREATER THAN 15°. The 15° slope was calculated with static stability measurements according 
to the requirements of BS EN ISO 5395-3.

4.8 ACCESSORIES

4.8.1 STRIPING KIT 

 

Product number TBD

4.8.2 MULCHING KIT

Kit Number TBD

4.8.3 ACCELERATOR BAGGER

Kit Number TBD

4.9 SUPPORT LITERATURE

Contact your Dixie Chopper Dealer for a complete listing of literature available for your mower.
Operator’s Manual: 700465
Mower Parts Manual: 700484
Service & Repair Manual: TBD

Temperature

Viscosity

Above 100° F (38° C)

SAE 30 or Synthetic SAE 5W-30

40° to 100° F (4° to 38° C)

SAE 30 or SAE 10W-30 or Synthetic SAE 5W-30

0° to 40° F (-18° to 4° C)

SAE 5W-30 or SAE 10W-30 or Synthetic SAE 5W-30

Below 0° F (-18° C)

SAE 5W-30 or Synthetic SAE 5W-30

SPECIFICATIONS

4

Содержание Pursuit 1832S





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды