Ditel KOSMOS BETA-M, Руководство пользователя

Страница: 50 / 52

THERMOCOUPLE and Pt100
nEt PEAK VAL roC
MENU 31
oFF on CoM doSE
MENU 32
oFF on CoM trAC
(*)
MENU 34
oFF on CoM trAC
MENU 31
oFF on CoM doSE
MENU 32
102
doSE
If has been programmed input “Load Cell, Potentiometer or Process”, only in the submenu 31 is possible to select the function “doSE”
WAY of WORKING of SETPOINT1 in MODE "doSE"
When the function “doSE” is selected on the setpoint 1 menu, can not choose the comparison value, since it will be on the net value of the display.
Nor can choose HI or LO mode as this will depend on whether the setpoint is positive (HI) or negative (LO) and the numerical value of setpoint will
have to be mandatory to program on the direct programming of setpoint values routine (keys ENTER and LIMIT).
When exit from menu 31 with “doSE” option selected, the setpoint is locked and it doesn’t work.
To start working have to enter on direct programming routine and gives it a value.
When you press ENTER, the set value is added to the net internal value of display (if positive, "and is automatically HI-mode) or subtracted (if
negative," and is put in LO-mode).
At this time, enables the operation of the setpoint 1.
Each time the display increases (HI) or decrease (LO) in a number of points equal to the programmed setpoint 1 value will activate the output
relay.
Likewise, if the logical function nº 30 has been programmed, the setpoint value will be added to the totalizer and increase the batch number in one
unit.
If you also enable pin which is scheduled this logic function, two parameters are displayed in the main and secondary displays.
Activation of the relay output last time has been programmed on parameter "dLY" Setpoint1 menu or, if selected mode "LATCH", will be
permanently activated until a reset is made of setpoints LATCH (logical function No. 25).
(*) It’s not possible to program "trAC" if on the menu 31 has been programmed "doSE"
110
102
doSE
If has been programmed input “Load Cell, Potentiometer or Process”, only in the submenu 31 is possible to select the function “doSE”
WAY of WORKING of SETPOINT1 in MODE "doSE"
When the function “doSE” is selected on the setpoint 1 menu, can not choose the comparison value, since it will be on the net value of the display.
Nor can choose HI or LO mode as this will depend on whether the setpoint is positive (HI) or negative (LO) and the numerical value of setpoint will
have to be mandatory to program on the direct programming of setpoint values routine (keys ENTER and LIMIT).
When exit from menu 31 with “doSE” option selected, the setpoint is locked and it doesn’t work.
To start working have to enter on direct programming routine and gives it a value.
When you press ENTER, the set value is added to the net internal value of display (if positive, "and is automatically HI-mode) or subtracted (if
negative," and is put in LO-mode).
At this time, enables the operation of the setpoint 1.
Each time the display increases (HI) or decrease (LO) in a number of points equal to the programmed setpoint 1 value will activate the output
relay.
Likewise, if the logical function nº 30 has been programmed, the setpoint value will be added to the totalizer and increase the batch number in one
unit.
If you also enable pin which is scheduled this logic function, two parameters are displayed in the main and secondary displays.
Activation of the relay output last time has been programmed on parameter "dLY" Setpoint1 menu or, if selected mode "LATCH", will be
permanently activated until a reset is made of setpoints LATCH (logical function No. 25).
(*) It’s not possible to program "trAC" if on the menu 31 has been programmed "doSE"
110