Ditel KOSMOS BETA-M, Руководство пользователя

Страница: 23 / 52

83
83
The following functions have been added:
1. Use setpoint 2 to detect max reading
The option ‘MAX’ is for non-filtered peak values and the option ‘MAX-F’ is for
filtered values.
The setpoint configuration options (latch, HI-LO mode, delay-hysteresis, blink)
are programmed as for a standard setpoint but some have different meanings
in this case, the setpoint value is the display value from which the unit begins
to read peaks, below this value the operation is disabled.
The delay/hysteresis value is the amount of time that the output will stay active
from the moment that a peak value is detected (except in mode latch).
The output activation occurs when the instrument detects that the measured
variable has stopped increasing its magnitude and is falling down or stable for a
number of readings programmable from 0 to 99.
The 'nº-LEC' parameter allows to program the number of readings to wait from
the last peak detection, before the input variable can be considered to grow up
no more (the instrument makes 16 readings per second).
2. Control the setpoint outputs by a command via RS232C or RS485
This facility is enabled by selecting the option 'CoM' in the setpoint on-oFF
menu level. The rest of the standard setpoint options are omitted in the
programming routine except selection of the display blink. The output status of
these setpoints cannot be changed by an overflow condition or a pass to the
programming mode.
3. The setpoints can be referred to the totalizer value
In this case the setpoint value is programmed in the second display. The rest of
the options are the same as for a standard setpoint.
-oFF-
on-oFF 32
-on-
on-oFF 32
-CoM-
on-oFF 32
-no-
-
bLInK 32
-YES-
-bLInK 32
-
CoMP
32
-
CoMP
32
±88888
LEVEL 32
00
nº LEC 32
-HI-
HI-Lo 32
-Lo-
HI-Lo 32
dLY 32 HYS 1 32
0000.0
dLY 32
00000
HYS 1 32
-no-
-LAtCH 32
-YES-
-LAtCH 32
-no-
-bLInK 32
-YES-
-bLInK 32
HYS 2 32
00000
HYS 2 32
ANNEXE A. SETPOINTS
-totAL
CoMP
32
The following functions have been added:
1. Use setpoint 2 to detect max reading
The option ‘MAX’ is for non-filtered peak values and the option ‘MAX-F’ is for
filtered values.
The setpoint configuration options (latch, HI-LO mode, delay-hysteresis, blink)
are programmed as for a standard setpoint but some have different meanings
in this case, the setpoint value is the display value from which the unit begins
to read peaks, below this value the operation is disabled.
The delay/hysteresis value is the amount of time that the output will stay active
from the moment that a peak value is detected (except in mode latch).
The output activation occurs when the instrument detects that the measured
variable has stopped increasing its magnitude and is falling down or stable for a
number of readings programmable from 0 to 99.
The 'nº-LEC' parameter allows to program the number of readings to wait from
the last peak detection, before the input variable can be considered to grow up
no more (the instrument makes 16 readings per second).
2. Control the setpoint outputs by a command via RS232C or RS485
This facility is enabled by selecting the option 'CoM' in the setpoint on-oFF
menu level. The rest of the standard setpoint options are omitted in the
programming routine except selection of the display blink. The output status of
these setpoints cannot be changed by an overflow condition or a pass to the
programming mode.
3. The setpoints can be referred to the totalizer value
In this case the setpoint value is programmed in the second display. The rest of
the options are the same as for a standard setpoint.
-oFF-
on-oFF 32
-on-
on-oFF 32
-CoM-
on-oFF 32
-no-
-
bLInK 32
-YES-
-bLInK 32
-
CoMP 32
-
CoMP 32
±88888
LEVEL 32
00
nº LEC 32
-HI-
HI-Lo 32
-Lo-
HI-Lo 32
dLY 32 HYS 1 32
0000.0
dLY 32
00000
HYS 1 32
-no-
-LAtCH 32
-YES-
-LAtCH 32
-no-
-bLInK 32
-YES-
-bLInK 32
HYS 2 32
00000
HYS 2 32
ANNEXE A. SETPOINTS
-totAL
CoMP 32