Directed Electronics Clifford 590.4X страница 9 Скачать руководство пользователя

Страница: 9 / 23

Remote Start Shutdown/Startup Diagnostics

Shutdown diagnostics: If the remote start activates but fails to stay running, the remote start module has the

ability to inform you of what may have caused the remote start failure. Before performing shutdown diagnos-

tics it is important that you let the remote start shut off on its own i.e. let it attempt to start 3 times then shut

down, if this is not done the unit will report the shutdown you used to shut off the remote start.

Note: Shutdown diagnostics does not report if the vehicles factory immobilizer is causing the problem.

To perform shutdown diagnostics:

1. With the ignition Off,

press

and

hold

the Control button (on Control Center).

Turn

the ignition On and then back Off while

holding

the Control button.

Release

the Control button.

Press

and

release

the Control button. The status LED flashes to report the last shutdown for one minute or

until the ignition is turned on, as shown in the following table:

Status LED Flashes

Shutdown Mode

1 flash

Runtime expired

2 flashes

Over-rev shutdown

3 flashes

Low or no RPM

4 flashes

Transmitter shutdown (or optional push button)

5 flashes

(+) Brake shutdown

6 flashes

(-) Hood shutdown

7 flashes

Timer mode/Turbo mode/Manual mode error *

8 flashes

Neutral safety shutdown

9 flashes

Low battery (voltage mode)

10 flashes

Alarm triggered **

11 flashes

Wait-to-start input timed out

* Timer mode error: Ignition is on or shutdown input is active when activating timer mode.

Turbo mode error: Turbo mode is programmed off, engine is not on or shutdown input is active.

Manual mode error: MTS mode not enabled.

** Alarm was triggered during remote start sequence.

Startup Diagnostics:

If the vehicle fails to activate the remote start, the remote start module will notify you via

your Responder HD 2-way remote control and will flash the parking lights on the vehicle to notify you of what

caused the no-start situation.

Parking Light Flashes

5 flashes

Brake wire is active

6 flashes

Hood pin wire is active

7 flashes

Manual transmission mode is enabled and not initialized.

8 flashes

Neutral safety wire has no ground or the neutral safety switch is Off.

Содержание Clifford 590.4X
























Результаты поиска

Содержание Clifford 590.4X

Отзывы:

Похожие инструкции для Clifford 590.4X

Бренды по названию

Популярные бренды

Directed Electronics Clifford 590.4X, Руководство по установке

Результаты поиска

Содержание Clifford 590.4X

Отзывы:

Похожие инструкции для Clifford 590.4X

Бренды по названию

Популярные бренды