Directed Electronics Clifford 590.4X Скачать руководство пользователя

Страница: 17 / 23

6. Turbo Mode

1. No turbo Mode: Turbo mode is not available

2. On – 1/3/5/10 minutes: Turbo Mode is available and, when activated, the engine will run for the

duration set per the selected option

7. Timer Mode Runtime

•

12/3/6/9 minutes: sets the runtime when the engine is started by the Timer Mode and SmartStart

features

8. Flex Relay Function

1. Ignition 2: the relay will emulate the Ignition 1 output during remote start

2. Accessory 2: the relay will emulate the Accessory 1 output during remote start

3. Starter 2: the relay will emulate the Starter output during remote start

9. Diesel Start Delay

1. Wait-to-start input: (-) input on the Grey/black (H2/20) WTS wire will delay the starter output until

the ground ceases.

2. Timed 15/30/45 seconds: delays the starter output per the selected option, the WTS wire does not

function.

10. Accessory during Diesel Start Delay

1. On: the Accessory outputs (H3/3 high current and H2/22 low current) will be ON during diesel

start delay

2. Off: the Accessory outputs (H3/3 high current and H2/22 low current) will be OFF during diesel

start delay

11. Status 2 Output (Blue/White H2/3 wire)

1. Status: the output will activate before the ignition outputs turn on, and de-activate after they turn off

during remote start

2. Latch rear defogger: the output activates 10 seconds after start if the interior temperature is below

55˚F. It turns off after 10 minutes or upon remote start off

3. Pulse rear defogger: the output activates (for 800 ms) 10 seconds after start if the interior temperature

is below 55˚F.

12. Parking Light Output

1. Constant: the lights will turn on solid during remote start

2. Pulsed: the lights will pulse on/off during remote start

3. Off: the lights will be off during remote start

13. Anti-grind Output

1. On: the high current starter relay will be activated during remote start as anti-grind protection.

2. Off: the high current starter relay will not be activated during remote start, no anti-grind protection

is available.

14. Tach Mode Starter Release

1. Normal: the starter output will release normally during cranking (50% of the learned tachometer

value)

2. Increase: the starter output will release later during cranking (at 35% of the learned tachometer

value)

3. Decrease: the starter output will release sooner during cranking (at 35% of the learned tachometer

value)

15. Vehicle Temp Auto Report

1. Off: the report during remote start is defeated

2. On: the report is sent every 2 minutes during remote start if the temperature has changed (+/-) 1

degree since the last report

16. Remote start Safelock

1. Off: the Door lock and Factory Alarm Re-arm outputs will maintain the current status (locked/un-

Содержание Clifford 590.4X
























Результаты поиска

Содержание Clifford 590.4X

Отзывы:

Похожие инструкции для Clifford 590.4X

Бренды по названию

Популярные бренды

Directed Electronics Clifford 590.4X, Руководство по установке

Результаты поиска

Содержание Clifford 590.4X

Отзывы:

Похожие инструкции для Clifford 590.4X

Бренды по названию

Популярные бренды