Dietz Sango Advanced F Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 44

Dietz Sango Advanced F Скачать руководство пользователя страница 27

• The automatic parking brake works only in the 'Drive' position.

• The freewheel lever must be set to the 'Push' position only if the wheelchair

is to be actually pushed. Set the freewheel switch to the 'Drive' position

immediately after pushing is finished.

• Never use the 'Push' position on a slope! When the freewheel lever is in the

'Push' position, the automatic parking brake is turned off. This could then result

in the wheelchair rolling downhill accidentally.

7.7. Storage of the wheelchair after use

When the wheelchair is not in use:

•

It must be stored in a dry place where it will not be affected by the weather.

• Do not position the wheelchair in direct sunlight. Parts of the wheelchair could

then become so hot that they could burn you.

•

The ambient temperature for storage should be no lower than -20˚C and no

higher than +65˚C.

• Disconnect batteries in case of longer storage without usage.

If you start using the wheelchair again after it has been in storage for a while, you

must check it again (see 7.1).

SANGO ADVANCED / SLIMLINE - 27

7 Using the wheelchair

«
...
25
26
27
28
29
...
»

Содержание Sango Advanced F













































Отзывы:

Нет отзывов