Dietz Sango Advanced F Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 44

Dietz Sango Advanced F Скачать руководство пользователя страница 25

7.4. Driving on slopes or ramps

With all settings in the neutral position

(see 6.1), slopes/ramps of ≤6˚ (10.5%) are

deemed to be part of the standard user

environment for the FWD without stability

being affected (figure 33). For the RWD

and MWD the applicable gradient is ≤10˚

(17.6%).

Slopes or ramps outside the standard

user environment

Driving on slopes/ramps that are steeper

than the maximum safe slope may lead

to safety risks in terms of stability. Driving

on such slopes/ramps requires the user to

practise extreme caution and full control.

Always drive carefully and never experiment! Follow the instructions given under

warnings!

The stability and performance of the wheelchair depend on many variables.

Wheelchairs are adapted to individual users. For this reason these variables will be

different from one wheelchair to another. You should therefore ensure that your

dealer provides you with sufficient information about how to use the wheelchair

and that the dealer informs you whether the specific adjustments or adaptations

for your situation will affect the handling of the wheelchair.

Warning

• Always drive up and down slopes/ramps slowly, concentrating on what you are

doing.

• Avoid any sudden, jolting movements.

• Avoid making an emergency stop on a slope/ramp.

•

The braking distance on a slope can be considerably greater than on a flat

surface.

• When on slopes/ramp, try to avoid changing direction as much as possible.

• Do not turn on a slope.

• Drive on slopes/ramps only when all adjustments (lift, tilt, recline) are in the

neutral position.

• Never drive up or down a slope/ramp backwards.

• Do not drive on slopes/ramp with loose gravel or a sandy surface, as one of the

drive wheels may slip or spin.

• Driving up or down a slope for long periods of time may result in the motor

overheating.

• We always recommend an anti-tip device for driving down slopes in a FWD

wheelchair.

• If you notice that your speed is being greatly reduced when driving up a slope,

select a route that is less steep.

• Prevent the wheelchair from reaching high speeds when driving down slopes.

SANGO ADVANCED / SLIMLINE - 25

≤10˚

≤6˚

33

7 Using the wheelchair

«
...
23
24
25
26
27
...
»

Содержание Sango Advanced F













































Отзывы:

Нет отзывов