manualshive.com logo in svg

Dickey-John Flex4, Руководство оператора

Поделиться
Скачать
Dickey-John Flex4 Скачать руководство пользователя страница 79

OPERATOR’S  MANUAL 

 

 

 
 
 
 
 
 
 
 
 

 

NOTE:   The Road Watch

TM

 

temperature sensor or Surface 
Patrol

TM 

temperature sensor 

must be disconnected and the 
DICKEY-john temperature 
sensor adapter connected to 
the main harness for successful 
calibration. If the DICKEY-john 
temperature sensor adapter is 
disconnected when calibration 
is performed, an error screen 
displays. 

AIR TEMPERATURE SENSOR 

An air temperature sensor monitors air temperature changes. When 
enabled, an alarm on the Operate screen identifies when defined air 
temperature changes occur. Refer to Road Temperature section for display 
appearance on Operate screen. 

To enable Air Temperature Sensor Values: 

1.  Air temperature sensor input values and calibration procedures are 

similar to road temperature sensors. Refer to Road Temperature 
Sensor section for entering values. 

 

Figure 68 

 

 

Air Temperature Sensor Screens 

 

 

 

IMPORTANT: The Road Watch

TM 

sensor adapter must be connected to 

the Flex4 interface cable that connects to the rate 
control module harness. The interface cable must be 
connected to the rate control module connectors labeled 
as Analog 1, 2, 3 or 4. The connection point for the road 
temperature and air temperature must be identified at 
the F9 Accessory Sensor screen. 

 

76 / SYSTEM PROGRAMMING 

Flex4 Pro

TM 

Control System 

6010541 Rev A 

Содержание Flex4

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды