manualshive.com logo in svg

Dickey-John Flex4, Руководство оператора

Поделиться
Скачать
Dickey-John Flex4 Скачать руководство пользователя страница 50

OPERATOR’S  MANUAL 

 

 

 
 

 

FLEX4 PRO

TM 

PROGRAMMING 

 

A keyboard is required to program and calibrate the system. The keyboard 
is removed after programming is complete. System will not allow entry of 
setup menus, calibration, or configuration without a keyboard attached. 

 

IMPORTANT: After plugging in the keyboard, the Flex4 

Pro

TM 

tablet 

screen must be touched first before the keyboard 
becomes active and usable. 

Function keys (F1 through F12) located at the top of the keyboard are used 
to display 12 menu screens that define desired system settings. 
Configuration parameters can be changed on menu screens by using the 
up and down arrow keys on the keyboard or by selecting the configuration 
parameter by screen touch. 

Access to menus using keyboard function keys include: 

•  F1 Operate screen 
•  F2 Granular Channel Setup 
•  F3 Liquid Channel Setup 
•  F4 Auxiliary S Granular/Liquid/Spinner Channel Setup 
•  F5 Auxiliary Granular/Liquid Channel Setup 
•  F6 Calibration 
•  F7 Diagnostics 
•  F8 Ground Speed Setup 
•  F9 Accessory Sensor Setup 
•  F10 System Setup 
•  F11 Output Module Setup 
•  F12 Data Logging 

 

PASSCODE RESTRICTIONS 

Two types of passcodes are optional and can be enabled to require a driver/ 
supervisor to: 

•  Login with a passcode before driver operation is allowed 
•  Login to gain access and change configuration setup values with a 

keyboard 

The system passcode settings are shipped as disabled. Passcodes can be 
enabled at the (F10) System screen (Driver Login Setup). 

Once passcode settings are enabled, the codes are required before a driver 
begins operation or configuration setup screens are accessed. Passcodes 
can be any combination of numbers up to 10 digits. 

 
 
 
 
 
 
 
 
 
 

Flex4 Pro

TM 

Control System 

6010541 Rev A 

FLEX4 PROTM PROGRAMMING / 47 

Содержание Flex4

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды