Dickey-John Flex4 Скачать руководство пользователя страница 47

Страница: 47 / 152

OPERATOR’S MANUAL

HYDRAULIC ACCESSORY TOOL OPERATION

To control an accessory tool during operation, press the

Rate Increase/

Decrease

buttons on the Operator Switch Module to increase and decrease

the hydraulic flow. The PWM signal percentage sent to the hydraulic valve
displays in the channel window.

Accessory tools shut off when:

– Ground speed reaches zero
– or the Auto On/Off switch is turned off.

An increase in ground speed activates the tool to the previous PWM
percentage.

The control channel is set to Manual without Feedback for this feature.
Refer to Granular Configuration Setup (F2).

Figure 45

Operate Screen with Manual Percentage Reading

Control

Channel

Salt

set

for

Manual

w/o

Feedback

CURRENT AND SEASON RUN TOTALS

The Totals screen provides accumulated material usage, miles, and hours
driven using Auto mode, Blast, and Pause functions. Total operating data
can be viewed in current run totals, season run totals, or by route.

NOTE: Totals by driver are viewable

only by exporting the data file to
a report software tool program.

Run totals are logged and recorded in the following ways:

• Total Miles (km), tons (metric/English), and gallons (liters) spread while

in automatic control mode for each control channel and product
spread.

• Miles (km), tons (metric/English), and gallons (liters) spread while in

Blast mode for each product spread.

• Total vehicle miles (km) driven
• Liquid gallons (liters) sprayed during prewetting and anti-icing

application

• Total time spent spreading granular, spraying liquid, and blasting
• Miles (km), tons (metric/English), and gallons (liters) spread while in

Pause mode

• Trip Log indicates total miles driven in Operate mode

44 / OPERATION

Flex4 Pro

Control System

6010541 Rev A

Содержание Flex4

























































































































































Результаты поиска

Содержание Flex4

Отзывы:

Бренды по названию

Популярные бренды

Dickey-John Flex4, Руководство оператора

Результаты поиска

Содержание Flex4

Отзывы:

Бренды по названию

Популярные бренды