manualshive.com logo in svg

Dickey-John Flex4, Руководство оператора

Поделиться
Скачать
Dickey-John Flex4 Скачать руководство пользователя страница 20

OPERATOR’S  MANUAL 

 

 

 
 

 

INSTALLATION 

 

OPERATOR SWITCH MODULE MOUNTING 
BRACKET 

The Operator Switch Module Bracket attaches the Operator Switch Module 
to the tablet and includes the following components: 

•  Main switch module mounting bracket 
•  3 Hex nuts 
•  4 washers 
•  3 nuts/3 washers 

 

OPERATOR SWITCH MODULE BRACKET AND TABLET 
MOUNTING PLATE 

Attach Tablet Mounting Plate to the Operator Switch Module Bracket: 

1.  Remove the 4 screws from the back of the tablet plate 
2. Align switch module bracket holes with the plate holes. 
3. Secure the bracket and plate with the 4 screws. 

Attach Switch Module to Operator Switch Module Bracket: 

4.  Align stud bolts (3) to the bracket opening and insert the switch 

module. 

5.  Align switch module so the connectors insert through the module 

bracket connector opening and the (3) switch module stud bolts insert 
through the bolt holes of the bracket assembly. 

6. Secure switch module to the bracket using (3) hex nuts and washers. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Flex4 Pro

TM 

Control System 

6010541 Rev A 

 

INSTALLATION / 17 

Содержание Flex4

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды