Delta UV ELP1016/3AM Скачать руководство пользователя страница 3

Страница: 3 / 26

ELP AM Series - Manual 2011 - 042011

Page 3

IMPORTANT SAFETY INSTRUCTIONS

WARNING: This product should be installed by a professional service technician or

similar person, qualified in electrical equipment installation. Improper Installation and/or

operation could cause serious injury, property damage, or death. Improper installation

and/or operation will void the Limited Warranty

WARNING: When using electrical products, basic precautions should always be

followed, including the following:

READ AND FOLLOW ALL INSTRUCTIONS

WARNING-A wire connector is provided on this unit to connect a minimum 8 AWG (8.4

mm2) solid copper conductor between this unit and any metal equipment, metal

enclosures of electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of

the unit.

WARNING – For indoor use only. This unit is not intended for outdoor use.

WARNING – This product must be connected to ground-fault circuit-interrupter.

WARNING –Risk of Electric Shock. Install at least 5 feet (1.5 m) from inside wall of hot

tub or spa or swimming pool using nonmetallic plumbing

SAVE THESE INSTRUCTIONS

Содержание ELP1016/3AM



























Результаты поиска

Содержание ELP1016/3AM

Отзывы:

Похожие инструкции для ELP1016/3AM

Бренды по названию

Популярные бренды

Delta UV ELP1016/3AM, Руководство по установке и обслуживанию

Результаты поиска

Содержание ELP1016/3AM

Отзывы:

Похожие инструкции для ELP1016/3AM

Бренды по названию

Популярные бренды