DeLonghi ETAM29.62X, Инструкция по эксплуатации

Страница: 22 / 23

21
18. DISPLAYED MESSAGES
DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY
FILL TANK Insufficient water in the tank (A20). Fill the tank with water and/or insert it correct-
ly, pushing it as far as it will go until it clicks
into place.
EMPTY GROUNDS CONTAINER The grounds container (A15) is full. Empty the grounds container and drip tray
(A14), clean and replace. Important: when
removing the drip tray, the grounds contain-
er must be emptied, even if it contains few
grounds. If this is not done, when you make the
next coffees, the grounds container may fill up
more than expected and clog the machine.
GROUND TOO FINE ADJUST
MILL The grinding is too fine and the coffee is deliv-
ered too slowly or not at all. Repeat coffee delivery and turn the grind-
ing adjustment dial (A23) (fig. 11) one click
clockwise towards 7 while the coffee mill is
in operation. If after making at least 2 coffees
delivery is still too slow, repeat the correction
procedure, turning the grinding adjustment
dial another click until delivery is correct (see
section “9.4 Adjusting the coffee mill”). If the
problem persists, make sure the water tank
(A20) is fully inserted.
If the water softener filter (C4) is present, an
air bubble may have been released inside the
circuit, obstructing delivery. Deliver a little water until the flow becomes
regular.
INSERT GROUNDS CONTAINER After cleaning, the grounds container (A15) has
not been replaced.
Remove the drip tray (A14) and insert the
grounds container.
ADD PRE-GROUND COFFEE
The "pre-ground coffee" function has been se-
lected without placing any pre-ground coffee
in the funnel (A4). Place pre-ground coffee in the funnel (A4) or
deselect the pre-ground function.
DESCALE The machine must be descaled. The descaling procedure described in section
“13. Descaling” needs to be performed.
LESS COFFEE Too much coffee has been used.
Select a milder taste by pressing the
icon (B4) (fig. 8) or reduce the quantity of pre-
ground coffee.
FILL BEANS CONTAINER The coffee beans have run out. Fill the beans container (A3) (fig. 12).
The pre-ground coffee funnel (A4) is clogged. Empty the funnel with the help of the brush
(C5) as described in section “12.8 Cleaning the
pre-ground coffee funnel”.
INSERT INFUSER ASSEMBLY The infuser (A19) has not been replaced after
cleaning. Insert the infuser as described in section ““12.9
Cleaning the infuser”.
GENERAL ALARM The inside of the appliance is very dirty. Clean the inside of the appliance thoroughly,
as described in section “13. Descaling”. If the
message is still displayed after cleaning, con-
tact a service centre.
PROBLEM POSSIBLE CAUSE REMEDY
The coffee is not hot. The cups were not preheated. Warm the cups by rinsing them with hot
water (Please note: you can use the hot water
function).
The internal circuits of the appliance
have cooled down because 2/3 min-
utes have elapsed since the last coffee
was made. Before making coffee, heat the infuser by
performing a rinse cycle (see section “8.1
Rinsing”).
A low coffee temperature is set. Set a higher coffee temperature in the menu
(section “8.9 Setting the temperature”).
The coffee is weak or not creamy
enough. The coffee is ground too coarsely. Turn the grinding adjustment dial (A23) one
click anticlockwise towards 1 while the coffee
mill is in operation (fig. 11). Continue one click
at a time until coffee delivery is satisfactory.
The effect is only visible after delivering 2
coffees (see section “9.4 Adjusting the coffee
mill”).
The coffee is unsuitable. Use pre-ground coffee for espresso machines.
The coffee is delivered too slowly or a
drop at a time. The coffee is ground too finely. Turn the grinding adjustment dial (A23) one
click clockwise towards 7 while the coffee mill
is in operation (fig. 11). Continue one click at
a time until coffee delivery is satisfactory. The
effect is only visible after delivering 2 coffees
(see section “9.4 Adjusting the coffee mill”).
Coffee does not come out of one or
both of the spouts. The coffee spouts (A10) are blocked. Clean the spouts with a toothpick (fig. 26).
The appliance does not come on It is not plugged into the mains socket. Plug into the mains socket.
The main switch (A16) is not turned on. Press the main switch (fig. 1).
The infuser cannot be extracted The appliance has not been turned off
correctly
Turn the appliance off by pressing the but-
ton (section “7. Turning the appliance off”).
The frothed milk has large bubbles The milk is not cold enough or is not
semi-skimmed. You should ideally use skimmed or semi-
skimmed milk at refrigerator temperature
(about 5°C). If the result is not as you wished,
try changing brand of milk.
19. TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact Customer Services.
WATER CIRCUIT EMPTY FILL
WATER CIRCUIT
HOT WATER
Press OK The water circuit is empty. Press OK (B1) and deliver water from the cap-
puccino maker (A8) until it flows out normally.
If the problem persists, make sure the water
tank (A20) is fully inserted.
REPLACE FILTER The water softener filter (C4) is exhausted. Replace the filter or remove it as described
in section “15. Water softener filter (*certain
models only)”.