Dell XPS 210 Скачать руководство пользователя страница 9

Страница: 9 / 52

Back to Contents Page

Removing and Installing Parts

Dell™ XPS™ 210 Service Manual

Memory

You can increase your computer memory by installing memory modules on the system board.

Your computer supports unbuffered, non-ECC, DDR2 memory.

DDR2 Memory Overview

DDR2 memory modules should be installed in

pairs of matched memory size, speed,

and

technology

. If the DDR2 memory modules are not installed in matched

pairs, the computer will continue to operate, but with a slight reduction in performance. See the label on the module to determine the module capacity.

The recommended memory configurations are:

A pair of matched memory modules installed in DIMM connectors 1 and 2 (white securing clips)

A pair of matched memory modules installed in DIMM connectors 1 and 2 and another matched pair installed in DIMM connectors 3 and 4 (black securing

clips)

If you install mixed pairs of DDR2 800-MHz (PC2-6400) and DDR2 533-MHz (PC2-4300) memory, the modules function at the speed of the slowest

module installed.

Be sure to install a single memory module in DIMM connector 1, the connector closest to the processor, before you install modules in the other

connectors.

Memory

Cards

Hard Drive

CD/DVD Drive

Floppy Drive (Optional)

Media Card Reader (Optional)

Heat Sink Assembly

Fan Assembly

Processor

Modem

Power Supply

System Board

Front I/O Panel

Battery

Front Panel

NOTE:

Buffered memory is not supported on this computer.

NOTE:

Always install DDR2 memory modules in the order indicated on the system board.

NOTICE:

Do not install ECC memory modules.

1 matched pair of memory modules in DIMM connectors 1 and 2 (white securing clips)

Содержание XPS 210





















































Результаты поиска

Содержание XPS 210

Отзывы:

Похожие инструкции для XPS 210

Бренды по названию

Популярные бренды

Dell XPS 210, Руководство по обслуживанию

Результаты поиска

Содержание XPS 210

Отзывы:

Похожие инструкции для XPS 210

Бренды по названию

Популярные бренды