Dell XPS 210 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 52

background image

1.

Follow the procedures in

Before You Begin

.

2.

Remove the CD/DVD drive, if installed (see

Removing a CD/DVD Drive

).

3.

Remove the two screws from either side of the heat sink assembly.

4.

Pivot the assembly towards the back of the computer and lift to remove.

Installing the Heat Sink Assembly

1.

Place the heat sink assembly back onto the heat sink assembly bracket.

2.

Rotate the heat sink assembly down towards the computer base and tighten the two captive screws.

3.

Replace the CD/DVD drive (see

Installing a CD/DVD Drive

).

4.

Replace the computer cover (see

Replacing the Computer Cover

).

Fan Assembly

Removing the Fan Assembly

1.

Follow the procedures in

Before You Begin

.

2.

Remove the CD/DVD drive, if installed (see

Removing a CD/DVD Drive

).

3.

Remove the heat sink assembly (see

Removing the Heat Sink Assembly

).

1

heat sink assembly

CAUTION:

The heat sink assembly can get very hot during normal operation. Be sure that the assembly has had sufficient time to cool before you

touch it.

NOTICE:

After you remove the heat sink assembly, lay the assembly on its side. Do not set the heat sink assembly upright or touch the thermal

interface to avoid damage to the thermal interface material on the underside.

NOTICE:

Ensure that the heat sink is correctly seated and secure.

CAUTION:

Before you begin any of the procedures in this section, follow the safety instructions in the

Product Information Guide

.

CAUTION:

The heat sink assembly can get very hot during normal operation. Be sure that the assembly has had sufficient time to cool before you

touch it.

«
...
21
22
23
24
25
...
»

Содержание XPS 210





















































Отзывы:

Нет отзывов

Похожие инструкции для XPS 210

Бренд: Tandy Страницы: 493

PowerMate 2000 Series

Бренд: NEC Страницы: 8

Бренд: NEC Страницы: 8

DIRECTION L - SERVICE

Бренд: NEC Страницы: 139

st5548 - Thin Client

Бренд: Compaq Страницы: 39

Бренд: A1Touch Страницы: 9

Бренд: Avalue Technology Страницы: 15

TRS-80 Color Computer 2

Бренд: Radio Shack Страницы: 44

System x3200 M3

Бренд: IBM Страницы: 42

Бренд: Toshiba Страницы: 8

TLCS-900 Family

Бренд: Toshiba Страницы: 751

Бренд: Nexcom Страницы: 25

Бренд: Nexcom Страницы: 78

Бренд: Nexcom Страницы: 92

NISE 3500M Series

Бренд: Nexcom Страницы: 120

Бренд: Medion Страницы: 2

Бренд: Medion Страницы: 37

Бренд: Medion Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды