Dell XPS 210 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 52

background image

Front I/O Panel

Removing the Front I/O Panel

1.

Follow the procedures in

Before You Begin

.

2.

Remove the heat sink (see

Removing the Heat Sink Assembly

).

3.

Remove the fan assembly (see

Removing the Fan Assembly

).

4.

Remove any additional components that restrict access to the I/O panel.

5.

Remove the screw that secures the front I/O panel to the computer.

6.

Pivot the I/O panel toward the back of the computer, and then carefully lift it up and out of the computer.

7.

Disconnect any cables that are attached to the front I/O panel.

8.

Remove the Diagnostic LED card.

a.

Remove the cable connected to the card.

b.

Press the Diagnostic LED card case release lever and slide the case towards the bottom of the chassis to release the card case from the chassis.

c.

Gently remove the LED card case from the computer.

Installing the I/O Panel

Follow the procedures in

Removing the Front I/O Panel

in reverse order.

To replace the Diagnostic LED card:

1.

Orient the five LED card case tabs with the slots in the chassis.

CAUTION:

Before you begin any of the procedures in this section, follow the safety instructions in the

Product Information Guide

.

CAUTION:

To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover.

1

screw

2

front I/O panel

CAUTION:

When reinstalling the fan, ensure that you do not pinch the wires that run between the system board and the fan.

NOTE:

Ensure that the card release lever is on top.

«
...
28
29
30
31
32
...
»

Содержание XPS 210





















































Отзывы:

Нет отзывов

Похожие инструкции для XPS 210

Бренд: IBM Страницы: 18

Бренд: IBM Страницы: 152

Бренд: IBM Страницы: 155

Бренд: Radio Shack Страницы: 52

Бренд: Risecom Corporation Страницы: 32

Бренд: Compaq Страницы: 69

Бренд: Moxa Technologies Страницы: 42

Бренд: Acer Страницы: 101

Бренд: Mitsubishi Electric Страницы: 30

apricot ls/vs550

Бренд: Mitsubishi Electric Страницы: 67

Бренд: Mitsubishi Electric Страницы: 80

Бренд: Mitsubishi Electric Страницы: 26

Apricot FT S Pentium Series

Бренд: Mitsubishi Electric Страницы: 18

Бренд: Mitsubishi Electric Страницы: 26

Бренд: Mitsubishi Electric Страницы: 101

Бренд: Mitsubishi Electric Страницы: 105

Бренд: Mitsubishi Electric Страницы: 81

Бренд: Mitsubishi Electric Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды