Dell XPS 210 Скачать руководство пользователя страница 35

Страница: 35 / 52

x1 slot bidirectional speed: 500 MB/sec

x16 slot bidirectional speed: 8 GB/sec

PCI Express:

connector

one x1

connector size

36 pins

connector data width (maximum)

one PCI Express lane

PCI Express:

connector

one x16

connector size

164 pins

connector data width (maximum)

16 PCI Express lanes

Drives

Externally accessible

one slimline 3.5-inch media bay

one slimline 5.25-inch drive bay

Available devices

Serial ATA drive, USB memory devices, floppy drive,
CD drive, DVD drive, DVD+RW drive, DVD/CD-RW
combo drive, DVD+/-RW drive, and Media Card
Reader

Internally accessible

one bay for 1-inch high hard drive

Connectors

External connectors:

IEEE 1394

one 6-pin powered back panel connector

one 6-pin powered front panel connector

Video

15-hole D-SUB connector

USB

10-pin header for optional Media Card Reader (3.5
inch bay device) and two front panel and six back
panel USB 2.0

–

compliant connectors

NOTE:

The 10-pin header connector used for the

optional Media Card Reader is populated with only
nine pins for keying purposes.

Audio

six back panel connectors for line-in, line-
out/headphone, rear surround sound, microphone,
side surround sound, and center/Low Frequency
Effects (LFE) channel

back panel S/PDIF connector

front panel miniature headphone connector for line-
out

front panel microphone connector

Network adapter

RJ45 connector

Modem

RJ11 (MDC 1.5) connector and internally accessible 3-
pin header that connects the modem to RJ11

Temperature Sensor

one 2-pin connector

System board connectors:

Serial ATA

two 7-pin connectors

Fan

two 5-pin connectors (one for the CPU fan and one
for the optional hard drive fan connector.)

PCI Express x1

36-pin connector

PCI Express x16

164-pin connector

USB

10-pin header for optional Media Card Reader (3.5-
inch bay device)

MDC

one 12-pin connector

Floppy connector

one 26-pin connector

Front panel

one 40-pin header

Power

one 2 x 12 connector

Processor power

one 2 x 2 connector

IEEE 1394

one 2 x 5 header

—

always connected by cable to the

front panel; supports front panel IEEE 1394 port

Содержание XPS 210





















































Результаты поиска

Содержание XPS 210

Отзывы:

Похожие инструкции для XPS 210

Бренды по названию

Популярные бренды

Dell XPS 210, Руководство по обслуживанию

Результаты поиска

Содержание XPS 210

Отзывы:

Похожие инструкции для XPS 210

Бренды по названию

Популярные бренды