background image

Back to Contents Page

 Coin-Cell Battery

Dell™ 500 Service Manual

Removing the Coin-Cell Battery

CAUTION: 

Before you begin any of the procedures in this section, follow the safety instructions in the

Product Information Guide

.

1.  Follow the instructions in 

Before You Begin

2.  Remove all memory modules (see 

Removing Memory Module(s)

). 

3.  Remove the hard drive (see 

Removing the Hard Drive

). 

4.  Remove the optical drive (see 

Removing the Optical Drive

). 

5.  Remove Mini-Card (see 

Removing Mini-Card

). 

6.  Remove the center control cover (see 

Removing the Center Control Cover

). 

7.  Remove the keyboard (see 

Removing the Keyboard

). 

8.  Remove the display assembly (see 

Removing the Display Assembly

). 

9.  Remove the internal card with Bluetooth wireless technology, if installed (see 

Removing the Internal Card With

Bluetooth® Wireless Technology

). 

10.  Remove the palm rest (see 

Removing the Palm Rest

). 

11.  Remove the ExpressCard cage (see 

Removing the ExpressCard Cage

). 

12.  Remove the processor thermal-cooling assembly (see 

Removing the Processor Thermal-Cooling Assembly

). 

13.  Remove the processor (see 

Removing the Processor Module

). 

14.  Remove the system board (see 

Removing the System Board Assembly

). 

15.  Use a plastic scribe to pry up the coin-cell battery from the slot. 

Содержание Vostro 500























































Отзывы: