Dell Vostro 500 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 54

background image

1 display assembly 2 antenna cables
3 display cable

4 hinge screws (4)

11. Lift the display assembly out of the computer.

Replacing the Display Assembly

CAUTION:

Before you begin the following procedure, follow the safety instructions in the

Product

Information Guide

.

1. Follow the instructions in

Before You Begin

.

2. Align the display hinges with the holes in the base of the computer, then lower the display into place.

3. Replace and tighten the four display assembly hinge screws.

4. Slide the antenna cables through the routing hole to the base of the computer.

5. Replace the display cable and antenna cables in their proper routing guides.

NOTE:

Ensure that the display cable, camera cable, and antenna cables are properly routed and secured beneath the

plastic tabs.

6. Connect the display cable to the display cable connector on the system board.

7. Replace the keyboard (see

Replacing the Keyboard

).

8. Replace the center control cover (see

Replacing the Center Control Cover

).

9. Close the display and turn the computer over.

«
...
24
25
26
27
28
...
»

Содержание Vostro 500























































Отзывы:

Нет отзывов

Похожие инструкции для Vostro 500

Бренд: IBM Страницы: 5

Бренд: IBM Страницы: 125

Бренд: ZEOS Страницы: 80

Chromebook PX14E

Бренд: Ctl Страницы: 12

Бренд: Fujitsu Страницы: 104

Бренд: Fujitsu Страницы: 394

Бренд: Fujitsu Страницы: 416

Бренд: Fujitsu Страницы: 415

Бренд: Fujitsu Страницы: 94

Generation N3000 M760s

Бренд: NEC Страницы: 126

VERSA 6060 WINDOWS 98 - UPGRADE INFORMATION

Бренд: NEC Страницы: 114

Бренд: Dell Страницы: 22

Alienware M18x R2

Бренд: Dell Страницы: 1

Satellite C655D-S50852

Бренд: Toshiba Страницы: 4

Satellite C655D-S5063

Бренд: Toshiba Страницы: 4

Satellite C655D-S5048

Бренд: Toshiba Страницы: 4

Satellite A665-S5184

Бренд: Toshiba Страницы: 4

Satellite A665-3DV12

Бренд: Toshiba Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды