manualshive.com logo in svg

Dell S3048-ON, Руководство по настройке

"Получите бесплатное руководство по настройке Dell S3048-ON на нашем сайте. Скачайте Configuration Manual для вашего удобства. Улучшите производительность своей сети с помощью этой мощной коммутаторной системы. Скачайте его с нашего веб-сайта прямо сейчас!"

Поделиться
Скачать
background image

IPv6 Peer Routing in VLT Domains Overview

VLT enables the physical links between two devices that are called VLT nodes or peers, and within a VLT domain, to be considered as a 
single logical link to external devices that are connected using LAG bundles to both the VLT peers. This capability enables redundancy 
without the implementation of Spanning tree protocol (STP), thereby providing a loop-free network with optimal bandwidth utilization.

IPv6 peer routing is supported on all the platforms that are compatible with IPv6 routing and support VLT. This functionality performs the 
following operations:

•

Forwarding control traffic to the correct VLT node when the control traffic reaches the wrong VLT node due to hashing at the VLT LAG 

level on the ToR.

•

Routing the data traffic which is destined to peer VLT node.

•

Synchronizing neighbor entries learned on VLT VLAN interfaces between the primary and secondary node.

•

Synchronizing the IP address of VLT VLAN interfaces between the VLT primary node and secondary node.

•

Performing routing on behalf of peer VLT nodes for a configured time period when a peer VLT node goes down.

When you configure Layer 3 VLT peer routing using the 

peer-routing

 command in VLT DOMAIN mode, it applies for both IPv4 and 

IPv6 traffic in VLT domains. Layer 3 VLT provides a higher resiliency at the Layer 3 forwarding level. Routed VLT allows you to replace 
VRRP with routed VLT to route the traffic from the Layer 2 access nodes. With neighbor discovery (ND) synchronization, both the VLT 
nodes perform Layer 3 forwarding on behalf of each other.

The neighbor entries are typically learned by a node using neighbor solicitation (NS) and ND messages. These NS or neighbor 
advertisement (NA) messages can be either destined to the VLT node or to any nodes on the same network as the VLT interface. These 
learned neighbor entries are propagated to another VLT node so that the peer does not need to relearn the entries.

IPv6 Peer Routing

When you enable peer routing on VLT nodes, the MAC address of the peer VLT node is stored in the ternary content addressable memory 
(TCAM) space table of a station. If the data traffic destined to a VLT node, node1, reaches the other VLT node, node2, owing to LAG-level 
hashing in the ToR switch, it is routed instead of forwarding the packet to node1. This processing occurs because of the match or hit for 
the entry in the TCAM of the VLT node2.

Synchronization of IPv6 ND Entries in a VLT Domain

Because the VLT nodes appear as a single unit, the ND entries learned via the VLT interface are expected to be the same on both VLT 
nodes. VLT V6 VLAN and neighbor discovery protocol monitor (NDPM) entries synchronization between VLT nodes is performed.

The VLT V6 VLAN information must synchronize with peer VLT node. Therefore, both the VLT nodes are aware of the VLT VLAN 
information associated with the peers. The CLI configuration and dynamic state changes of VLT V6 VLANs are notified to peer VLT node. 
The ND entries are generally learned by a node from Neighbor advertisements (NA).

ND entries synchronization scenarios:

•

When you enable and configure VLT on both VLT node1 and node2, any dynamically learned ND entry in VLT node1 be synchronizes 
instantaneously to VLT node2 and vice-versa. The link-local address also synchronizes if learned on the VLT VLAN interface.

•

During failure cases, when a VLT node goes down and comes back up all the ND entries learned via VLT interface must synchronize to 
the peer VLT node.

Virtual Link Trunking (VLT)

939

Содержание S3048-ON













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S3048-ON

CALIENT S320 Hardware User'S Manual preview
S320
Бренд: CALIENT Страницы: 46
CALIENT S320 Getting Started Manual preview
S320
Бренд: CALIENT Страницы: 42
B&B Electronics 485DSS Manual preview
485DSS
Бренд: B&B Electronics Страницы: 26
B&B Electronics 232XS5 Instruction Manual preview
232XS5
Бренд: B&B Electronics Страницы: 15
B&B Electronics 232BSS4 Instruction Manual preview
232BSS4
Бренд: B&B Electronics Страницы: 45
X10 WM100 Product Manual preview
WM100
Бренд: X10 Страницы: 20
Edimax GS-1016 Datasheet preview
GS-1016
Бренд: Edimax Страницы: 2
ORVIBO ZigBee Mini Hub Faq preview
ZigBee Mini Hub
Бренд: ORVIBO Страницы: 3
GALCO EX95000 Series Quick Start Manual preview
EX95000 Series
Бренд: GALCO Страницы: 22
Amped Wireless APA2600M Installation And Configuration Manual preview
APA2600M
Бренд: Amped Wireless Страницы: 22
YA Fusion Z-7799 Instruction Manual preview
Fusion Z-7799
Бренд: YA Страницы: 47
Greengate VNLW-P-1001-MV-N-V Installation Instructions preview
VNLW-P-1001-MV-N-V
Бренд: Greengate Страницы: 2
Key Digital HD Flash 4 KD-SW4x1 Operating Instructions Manual preview
HD Flash 4 KD-SW4x1
Бренд: Key Digital Страницы: 12
Rockwell Automation Allen-Bradley 800F-ALR1 Installation Instructions preview
Allen-Bradley 800F-ALR1
Бренд: Rockwell Automation Страницы: 2
Black Box LB9007A-SC-R Installation preview
LB9007A-SC-R
Бренд: Black Box Страницы: 2
NewStar NS-211KA User Manual preview
NS-211KA
Бренд: NewStar Страницы: 10
Guntermann & Drunck UCON/s Getting Started preview
UCON/s
Бренд: Guntermann & Drunck Страницы: 8
ROSSMA IIOT-AMS Tilt Counter Operation Manual preview
IIOT-AMS Tilt Counter
Бренд: ROSSMA Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды