Dell PowerEdge C4130 Скачать руководство пользователя страница 215 | Manualshive

Страница: 215 / 217

background image

Troubleshooting a GPU

NOTE: The GPU is a Field Replaceable Unit. Do not to troubleshoot the GPU without the assistance
of a Dell certified service technician.

For more information, see the Getting help section.

CAUTION: Many repairs may only be done by a certified service technician. You should only
perform troubleshooting and simple repairs as authorized in your product documentation, or as
directed by the online or telephone service and support team. Damage due to servicing that is
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that are shipped with your product.

Related Links

System messages

For a list of event and error messages generated by the system firmware and agents that monitor system

components, see the Dell Event and Error Messages Reference Guide at

Dell.com/openmanagemanuals

>

OpenManage software

.

Warning messages

A warning message alerts you to a possible problem and prompts you to respond before the system
continues a task. For example, before you format a hard drive, a message warns you that you may lose all
data on the hard drive. Warning messages usually interrupt the task and require you to respond by typing
y (yes) or n (no).

NOTE: Warning messages are generated by either the application or the operating system. For more
information, see the documentation that accompanied the operating system or application.

Diagnostic messages

The system diagnostic utilities may issue messages if you run diagnostic tests on your system. For more
information about system diagnostics, see the Using System Diagnostics section.

Related Links

Using system diagnostics

Alert messages

The systems management software generates alert messages for your system. Alert messages include
information, status, warning, and failure messages for drive, temperature, fan, and power conditions. For
more information, see the systems management software documentation.

215

«
...
213
214
215
216
217
»

Содержание PowerEdge C4130


























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge C4130

Бренд: Kaleidescape Страницы: 11

Бренд: Acano Страницы: 17

Бренд: Rackable Systems Страницы: 4

Бренд: Nortel Страницы: 144

Connectware PortServer TS 8/16

Бренд: Digi Страницы: 106

Бренд: Excito Страницы: 46

Бренд: 7th Sense Страницы: 24

Snap Server 18000

Бренд: Adaptec Страницы: 5

Бренд: Intel Страницы: 78

STRATOS S210 Series S210-X2A2J

Бренд: QUANTA Страницы: 262

STRATOS S210 Series S210-X12RS

Бренд: QUANTA Страницы: 272

Бренд: Intel Страницы: 67

X38ML - Server Board Motherboard

Бренд: Intel Страницы: 132

Бренд: Acnodes Страницы: 98

Бренд: Oracle Страницы: 4

Бренд: Oracle Страницы: 108

Бренд: FieldServer Страницы: 34

Бренд: FaxFinder Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды