background image

Dell™ PowerEdge™ 700 Systems Installation and Troubleshooting Guide

 

Introduction

 

Indicators and Codes

 

Finding Software Solutions

 

Running System Diagnostics

 

Troubleshooting Your System

 

Installing System Options

 

Installing Drives

 

Getting Help

 

Jumpers and Connectors

 

I/O Connectors

 

Abbreviations and Acronyms

 

 

Notes, Notices, and Cautions  

 

Abbreviations and Acronyms  

For a complete list of abbreviations and acronyms, see "

Abbreviations and Acronyms

." 

Information in this document is subject to change without notice. 

© 2003 Dell Inc. All rights reserved.

 

Reproduction in any manner whatsoever without the written permission of Dell Inc.

 

is strictly forbidden. 

Trademarks used in this text: 

Dell

, the 

DELL

 logo, 

PowerEdge, Dell OpenManage, Dell Precision, Dimension, Inspiron, OptiPlex, Latitude

DellNet

PowerVault

PowerApp

, and 

Axim 

are 

trademarks of Dell Inc.; 

Intel

Pentium

, and 

Celeron 

are registered trademarks of Intel Corporation; 

Microsoft

,

 MS-DOS

,

 

and 

Windows

 are registered trademarks of Microsoft 

Corporation. 

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any 
proprietary interest in trademarks and trade names other than its own. 

 

Initial release: November 2003

 

NOTE: 

A NOTE indicates important information that helps you make better use of your computer. 

NOTICE: 

A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. 

 

CAUTION: 

A CAUTION indicates a potential for property damage, personal injury, or death.

Содержание PowerEdge 700































































































Отзывы: