manualshive.com logo in svg

Dell PowerConnect W-IAP175P, Руководство пользователя

Поделиться
Скачать
Dell PowerConnect W-IAP175P Скачать руководство пользователя страница 84

84

  |  Authentication

Dell PowerConnect W-Series Instant Access Point 6.1.2.3-2.0.0.0

  | User Guide

Tunnel-Medium-Type

Tunnel-Preference

Tunnel-Private-Group-Id

Tunnel-Server-Auth-Id

Tunnel-Server-Endpoint

Tunnel-Type

User-Category

User-Name

User-Vlan

Vendor-Specific

Management Authentication Settings

To authenticate the Virtual Controller Management in the Instant UI, perform the following steps:

1. Click the 

Settings

 link.

2. Select the 

Admins 

tab.

3. In the 

Authentication

 drop-down list, select any one of the following:

Internal

—Select the 

Username 

and 

Password

 specified in the respective text boxes to access the Virtual 

“Configuring an External RADIUS Server” on page

 

79

 Management UI.

RADIUS Server

—Specify one or two radius servers to authenticate UI. If two servers are configured users can 

use them in primary/backup mode or load-balancing mode, this is identical to the radius server configuration 
for SSIDs. For information on configuring external RADIUS server, see 

“External RADIUS Server” on 

page

 

78

.

RADIUS server w/ fallback to internal

—Specify the radius servers as well as a Username and Password. If 

there is no response from the RADIUS server (RADIUS server timeout), the authentication will switch to 
“Internal”.

Figure 65  

Management Authentication Settings

4. Click 

OK

.

Содержание PowerConnect W-IAP175P































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды