manualshive.com logo in svg

Dell PowerConnect W-IAP175P, Руководство пользователя

Поделиться
Скачать
Dell PowerConnect W-IAP175P Скачать руководство пользователя страница 153

Dell PowerConnect W-Series Instant Access Point 6.1.2.3-2.0.0.0

  |  User Guide 

Regulatory Domain  |  

153

Chapter 21

Regulatory Domain

The IEEE 802.11/b/g/n Wi-Fi networks operate in 2.4 GHz and IEEE 802.11a/n operate in 5.0 GHz spectrum. 
These spectrums are divided into channels. The 2.4 GHz spectrum is divided into 14 overlapping, staggered 20 
MHz wireless carrier channels. These channels are spaced 5 MHz apart. The 5 GHz spectrum is divided into more 
channels. The channels that can be used in a particular country differ based on the regulations of that country.

The initial Wi-Fi setup requires you to specify the country code for the country in which the Dell Instant will 
operate. This configuration sets the regulatory domain for the radio frequencies that the IAPs use. Within the 
regulated transmission spectrum, a high-throughput 802.11a, 802.11b/g, or 802.11n radio setting can be 
configured. The available 20 MHz and 40 MHz channels are dependent on the specified country code.

You cannot change the country code for the IAPs designated for US, Japan, and Israel. Improper country code 
assignment can disrupt wireless transmissions. Most countries impose penalties and sanctions on operators of 
wireless networks with devices set to improper country codes. 

Table 27

 shows the list of country codes.

Figure 115  

Specifying a Country Code

Содержание PowerConnect W-IAP175P































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды