Dell Inspiron One 2305 Скачать руководство пользователя страница 74

Страница: 74 / 96

Internal Card With Bluetooth® Wireless Technology: Dell Inspiron One 2305/2310 Service Manual

file:///T|/htdocs/systems/InsOne2310/sr/sm/btooth.htm[7/25/2012 10:25:04 AM]

Back to Contents Page

Internal Card With Bluetooth® Wireless Technology

Dell™ Inspiron™ One 2305/2310 Service Manual

Removing the Bluetooth Card

Replacing the Bluetooth Card

WARNING:

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage at

www.dell.com/regulatory_compliance.

CAUTION:

Only a certified service technician should perform repairs on your computer. Damage due to

servicing that is not authorized by Dell™ is not covered by your warranty.

CAUTION:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by

periodically touching an unpainted metal surface (such as a connector on your computer).

If you ordered a card with Bluetooth wireless technology with your computer, it is already installed.

Removing the Bluetooth Card

1. Follow the instructions in

Before You Begin

2. Remove the system board (see

Removing the System Board

3. Follow the instructions from

step 5

step 11

Removing the Display Bezel

4. Turn the display bezel over.

5. Remove the mylar sleeve from the Bluetooth card.

6. Remove the two screws that secure the Bluetooth card to the display bezel.

7. Disconnect the Bluetooth-card cable from the connector on the Bluetooth card.

8. Lift the Bluetooth card away from the display bezel.

Bluetooth card

Bluetooth-card cable

screws (2)

Содержание Inspiron One 2305

































































































Результаты поиска

Содержание Inspiron One 2305

Отзывы:

Похожие инструкции для Inspiron One 2305

Бренды по названию

Популярные бренды

Dell Inspiron One 2305, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron One 2305

Отзывы:

Похожие инструкции для Inspiron One 2305

Бренды по названию

Популярные бренды