background image

Rear Stand Cover: Dell Inspiron One 2305/2310 Service Manual

file:///T|/htdocs/systems/InsOne2310/sr/sm/stand_co.htm[7/25/2012 10:24:48 AM]

Back to Contents Page

 Rear Stand Cover

Dell™ Inspiron™ One 2305/2310 Service Manual

  

Removing the Rear Stand Cover

  

Replacing the Rear Stand Cover

WARNING: 

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage at

www.dell.com/regulatory_compliance.

CAUTION: 

Only a certified service technician should perform repairs on your computer. Damage due to

servicing that is not authorized by Dell™ is not covered by your warranty.

CAUTION: 

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by

periodically touching an unpainted metal surface (such as a connector on your computer).

Removing the Rear Stand Cover

1.  Follow the instructions in 

Before You Begin

2.  Remove the back cover (see 

Removing the Back Cover

). 

3.  Follow the instructions from 

step 2

 to 

step 5

 in 

Removing the Front Stand

4.  Lift and hold the rear stand and release the rear stand cover from its position. 

5.  Slide out the rear stand cover through the rear stand. 

1

rear stand cover

2

rear stand

Replacing the Rear Stand Cover

1.  Follow the instructions in 

Before You Begin

2.  Slide the rear stand cover through the rear stand. 

Содержание Inspiron One 2305

































































































Отзывы: