Dell Inspiron One 2305 Скачать руководство пользователя страница 57

Страница: 57 / 96

Processor Heat-Sink Fan: Dell Inspiron One 2305/2310 Service Manual

file:///T|/htdocs/systems/InsOne2310/sr/sm/hs_fan.htm[7/25/2012 10:24:58 AM]

Back to Contents Page

Processor Heat-Sink Fan

Dell™ Inspiron™ One 2305/2310 Service Manual

Removing the Processor Heat-Sink Fan

Replacing the Processor Heat-Sink Fan

WARNING:

Before working inside your computer, read the safety information that shipped with your

computer. For additional safety best practices information, see the Regulatory Compliance Homepage at

www.dell.com/regulatory_compliance.

WARNING:

The heat sink may be very hot during normal operation. Ensure that it has had sufficient time

to cool before you touch it.

CAUTION:

Only a certified service technician should perform repairs on your computer. Damage due to

servicing that is not authorized by Dell™ is not covered by your warranty.

CAUTION:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by

periodically touching an unpainted metal surface (such as a connector on your computer).

Removing the Processor Heat-Sink Fan

1. Follow the instructions in

Before You Begin

2. Remove the back cover (see

Removing the Back Cover

3. Follow the instructions from

step 2

step 5

Removing the Front Stand

4. Remove the system-board shield (see

Removing the System-Board Shield

5. Disconnect the processor heat-sink fan cable from the connector (CPU FAN) on the system board.

6. Remove the two screws that secure the processor heat-sink fan to the chassis.

7. Carefully peel the silver foil from the processor heat sink.

8. Lift the processor heat-sink fan along with its cable away from the chassis.

NOTE:

The appearance of the system board may vary based on your computer model.

Содержание Inspiron One 2305

































































































Результаты поиска

Содержание Inspiron One 2305

Отзывы:

Похожие инструкции для Inspiron One 2305

Бренды по названию

Популярные бренды

Dell Inspiron One 2305, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron One 2305

Отзывы:

Похожие инструкции для Inspiron One 2305

Бренды по названию

Популярные бренды