Dell Inspiron 1318 Скачать руководство пользователя страница 1

Страница: 1 / 46

Dell™ Inspiron™ 1318 Service Manual

Notes, Notices, and Cautions

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text:

Dell

, the

DELL

logo, a n d

Inspiron

are trademarks of Dell Inc.;

Bluetooth

is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell

under license;

Microsoft

Windows, Windows Vista,

a n d

Windows Vista start button

are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or

other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.

July 2008 Rev. A00

Model PP25L

Internal Card With Bluetooth

Wireless Switch Assembly

Charger Board

Battery Latch Assembly

Flashing the BIOS

NOTE:

A NOTE indicates important information that helps you make better use of your computer.

NOTICE:

A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION:

A CAUTION indicates a potential for property damage, personal injury, or death.

Содержание Inspiron 1318















































Результаты поиска

Содержание Inspiron 1318

Отзывы:

Похожие инструкции для Inspiron 1318

Бренды по названию

Популярные бренды

Dell Inspiron 1318, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 1318

Отзывы:

Похожие инструкции для Inspiron 1318

Бренды по названию

Популярные бренды