Dell FS7500 Скачать руководство пользователя

Страница: 28 / 88

Inserting Each Power Module into the BPS Chassis

To insert a power module into the BPS chassis, see

Figure 20

and follow these steps:

1. Lift the power module.

2. Carefully slide the power module into the BPS chassis. The center latch clicks when the module is properly

installed.

Figure 20: Inserting a Power Module Into the BPS Chassis

Attaching the BPS Bezel

To attach the BPS bezel to the front of the chassis, see

Figure 21

and follow these steps:

1. Locate the BPS chassis bezel that was delivered in the accessory box with the BPS.

2. Gently fit the bezel onto the right side of the chassis (Callout 1).

3. Lift the latch on the left side of the bezel. Push the left side of the bezel onto the left side of the chassis to

engage the bezel with the front of the chassis (Callout 2). Release the latch.

EqualLogic FS7500 Installation and Setup

2 Hardware Rack Mounting

Содержание FS7500

























































































Результаты поиска

Содержание FS7500

Отзывы:

Похожие инструкции для FS7500

Бренды по названию

Популярные бренды

Dell FS7500, Установка и настройка

Результаты поиска

Содержание FS7500

Отзывы:

Похожие инструкции для FS7500

Бренды по названию

Популярные бренды