Dell FS7500 Скачать руководство пользователя

Страница: 12 / 88

FS7500 Controller Technical Specifications

Table 2: FS7500 Controller Technical Specifications

Attribute

Value

Weight of controller

39 pounds or 17.69 kilograms

Operating temperature

50 to 95 degrees F (10 to 35 degrees C)

Storage temperature

-40 to 149 degrees F (-40 to 65 degrees C)

Operating altitude

-50 to 10,000 feet (-16 to 3048 meters)

Operational relative humidity

20 to 80 percent non-condensing

Thermal output (fully-loaded controller)

2446.5 BTU/hr maximum (High Output)
1712.9 BTU/hr maximum (Energy Smart)

Operational shock

Half sine shock in all operational orientations of 31G plus or
minus 5% with a pulse duration of 2.6 ms plus or minus 10%

Operational vibration

0.26 Gms from 5-350 Hz for 5 minutes in operational
orientations

Input voltage

90 to 264 VAC (auto-sensing)

Input frequency

47 - 63 Hz

System input power

90-264 VAC, autoranging, 47-63 Hz

Each power supply

502 W
Input current: up to 55 A per power supply for 10 ms or less

Dimensions

1.68 in. height x 18.99 in. width x 30.39 in. depth
(4.26 cm height x 48.24 cm width x 77.2 cm depth)

FS7500 Backup Power Supply Technical Specifications

Table 3: FS7500 Backup Power Supply Technical Specifications

Attribute

Value

Weight of fully-loaded BPS

66.1 pounds (30 kilograms)

Operating temperature

32 to 104 degrees F (0 to 40 degrees C)

Storage temperature

5 to 113 degrees F (-15 to 45 degrees C)

Operating altitude

10,000 feet (3048 meters)

Operational relative humidity

0 to 95 percent non-condensing

Input voltage

120 V models: 90-140 V, auto-sensing

230 V models: 180-264 V, auto-sensing

Input frequency

50 - 60 Hz (auto-sensing), +/- 3 Hz

Power levels

500 W DC output

Dimensions

17.1 in. x 1.6 in. x 28.5 in. (434 cm x 42 cm x 723 cm)

EqualLogic FS7500 Installation and Setup

1 Before You Begin

Содержание FS7500

























































































Результаты поиска

Содержание FS7500

Отзывы:

Похожие инструкции для FS7500

Бренды по названию

Популярные бренды

Dell FS7500, Установка и настройка

Результаты поиска

Содержание FS7500

Отзывы:

Похожие инструкции для FS7500

Бренды по названию

Популярные бренды