Dell FS7500 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 88

background image

Preface

A PS Series group provides iSCSI-accessible block storage. With the latest version of the
PS Series firmware and the addition of an EqualLogic FS7500, the same PS Series group can provide block
storage and support for NAS (Network Attached Storage).

The EqualLogic FS7500 includes:

•

Two FS7500 Controller units with pre-installed file serving software

•

One FS7500 Backup Power Supply System (BPS) unit

This manual describes how to install EqualLogic FS7500 hardware and configure a NAS service.

Note:

An EqualLogic FS7500 requires a PS Series group running the PS Series Firmware Version 5.1 or 5.2.

Audience

This manual is designed for the administrators responsible for installing EqualLogic FS7500 hardware.
Administrators are

not

required to have extensive network or storage system experience. However, it may be

useful to understand:

•

Basic networking concepts

•

Current network environment

•

User disk storage requirements

•

RAID configurations

•

Disk storage management

Note:

Although this manual provides examples of using an EqualLogic FS7500 in some common network

configurations, detailed information about setting up a network is beyond its scope.

Organization

This manual is organized as follows:

•

Chapter 1, Before You Begin

, describes the preliminary tasks you must perform before beginning the

installation.

•

Chapter 2, Hardware Rack Mounting

, describes how to install the BPS and controller hardware in a rack.

•

Chapter 3, Power Connections

, describes how to connect the BPS and controllers to power.

•

Chapter 4, Network Cable Connections

, describes how to connect the controllers to the networks.

•

Chapter 5, NAS Service Configuration

, describes how to discover controllers and set up a NAS service.

iii

«
...
3
4
5
6
7
...
»

Содержание FS7500

























































































Отзывы:

Нет отзывов

Похожие инструкции для FS7500

Бренд: B+B SmartWorx Страницы: 4

Бренд: Cabletron Systems Страницы: 21

Бренд: Cambium Networks Страницы: 68

Бренд: Cambium Networks Страницы: 110

Бренд: ICP DAS USA Страницы: 8

Бренд: Watchguard Страницы: 39

Бренд: Maxim Страницы: 26

Бренд: NetComm Страницы: 3

OCTOPUS 5TX-EEC

Бренд: Hirschmann Страницы: 6

EdgeLens INT10G8LR56

Бренд: Garland Страницы: 30

Бренд: ActionTec Страницы: 115

Бренд: Hama Страницы: 25

Бренд: Infoblox Страницы: 16

Бренд: Digi Страницы: 75

Ultra WiFi Booster

Бренд: Optus Страницы: 8

EK-Quantum Vector FTW3 RTX 2080 Ti

Бренд: ekwb Страницы: 3

Бренд: Xtreme Страницы: 83

VXC-114U Series

Бренд: ICP DAS USA Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды