Dell FS7500 Скачать руководство пользователя страница 36

Страница: 36 / 88

Warning:

Make sure the voltage of your power source is compatible with the voltage rating of the BPS. If the
power source voltage is too low, the BPS will not activate. If the voltage is too high, the BPS can be
destroyed.

To connect a BPS power module to a power source, follow these steps:

1. Obtain a power cable with a C13 connector and a connector that fits the receptacle of your power source, in

addition to a hook-and-loop fastener provided in the BPS shipping box.

If power cables are not in the shipping box, see your PS Series support provider or reseller for power cable
information.

2. Open the latch for the C14 input connector on the power module (on the right side of the power module) and

insert the cable’s C13 connector. See

Figure 27

3. Connect the power cable to a power source.

4. Use the hook-and-loop fastener strip to secure the power cable to the latch on the power module. This

provides strain relief for the cable. See

Figure 28

Figure 27: Connecting a BPS Power Module to a Power Source

EqualLogic FS7500 Installation and Setup

3 Power Connections

Содержание FS7500

























































































Результаты поиска

Содержание FS7500

Отзывы:

Похожие инструкции для FS7500

Бренды по названию

Популярные бренды

Dell FS7500, Установка и настройка

Результаты поиска

Содержание FS7500

Отзывы:

Похожие инструкции для FS7500

Бренды по названию

Популярные бренды