Dell EMC PowerEdge T440 Скачать руководство пользователя страница 90

Страница: 90 / 150

Figure 42. x8 drive backplane

ODD power connector

backplane P4 power connector

backplane sideband signal connector

Mini SAS SAS_A0

Mini SAS SAS_B0

Removing a hard drive backplane

Prerequisites

CAUTION:

To prevent damage to the drives and backplane, you must remove the hard drives from the system before removing

the backplane.

CAUTION:

You must note the number of each hard drive and temporarily label them before removal so that you can replace them

in the same locations.

Follow the safety guidelines listed in

Safety instructions

Follow the procedure listed in

Before working inside your system

If installed, remove the bezel.

Remove all the drives.

Remove the air shroud.

Steps

Disconnect the data, signal, and power cables from the backplane.

NOTE:

For the x8 backplane, press the SAS connector and push the connector toward the top of the system to release the

SAS cable from the backplane.

Pull the release pin and holding the pin, lift the backplane out of the system.

Installation and Service Manual
Installing and removing system components

Содержание EMC PowerEdge T440























































































































































Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды

Dell EMC PowerEdge T440, Руководство пользователя

Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды