Dell EMC PowerEdge T440 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 150

background image

Drive indicator codes

Each drive carrier has an activity LED indicator and a status LED indicator. The indicators provide information about the current status of
the drive. The activity LED indicator indicates whether the drive is currently in use or not. The status LED indicator indicates the power
condition of the drive.

Figure 8. Drive indicators

1

Drive activity LED indicator

2

Drive status LED indicator

3

Drive

NOTE:

If the drive is in the Advanced Host Controller Interface (AHCI) mode, the status LED indicator does not turn on.

Table 4. Drive indicator codes

Drive status indicator code

Condition

Flashes green twice per second

Identifying drive or preparing for removal.

Off

Drive ready for removal.

NOTE:

The drive status indicator remains off until all drives are

initialized after the system is turned on. Drives are not ready
for removal during this time.

Flashes green, amber, and then turns off

Predicted drive failure.

Flashes amber four times per second

Drive failed.

Flashes green slowly

Drive rebuilding.

Solid green

Drive online.

Flashes green for three seconds, amber for three seconds, and
then turns off after six seconds

Rebuild stopped.

Installation and Service Manual

Dell EMC PowerEdge T440 overview

17

«
...
15
16
17
18
19
...
»

Содержание EMC PowerEdge T440























































































































































Отзывы:

Нет отзывов

Похожие инструкции для EMC PowerEdge T440

MCX-2000 - MusicCAST Digital Audio Server

Бренд: Yamaha Страницы: 25

Бренд: Axis Страницы: 10

Бренд: Altos Страницы: 93

Бренд: TAPKO Страницы: 2

MediaGrid ContentServer 3000

Бренд: Omneon Страницы: 2

Eternus DX80 S2

Бренд: Fujitsu Страницы: 186

Бренд: Fujitsu Страницы: 242

Бренд: ABB Страницы: 9

Бренд: ABB Страницы: 68

Бренд: Honeywell Страницы: 8

Бренд: Honeywell Страницы: 16

Бренд: Honeywell Страницы: 56

Uniformance R300

Бренд: Honeywell Страницы: 60

Бренд: Honeywell Страницы: 66

Бренд: Honeywell Страницы: 88

Бренд: Honeywell Страницы: 97

Бренд: Honeywell Страницы: 108

MES3-255C-DM-EN

Бренд: Mitsubishi Electric Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды