Dell EMC PowerEdge T440 Скачать руководство пользователя страница 70

Страница: 70 / 150

Figure 22. Installing the air shroud

Next step

Follow the procedure listed in

After working inside your system

Drives

Drives are supplied in hot swappable drive carriers that fit in the drive slots.

CAUTION:

Before attempting to remove or install a drive while the system is running, see the documentation for the storage

controller card to ensure that the host adapter is configured correctly.

CAUTION:

Do not turn off or restart your system while a drive is being formatted. Doing so can cause a drive failure.

When you format a drive, allow enough time for the formatting to complete. Be aware that high-capacity drives can take a long time to
format.

Removing a drive blank

The procedure for removing 2.5 inch and 3.5 inch drive blanks is identical.

Prerequisites

Follow the safety guidelines listed in

Safety instructions

If installed, remove the front bezel.

CAUTION:

To maintain proper system cooling, drive blanks must be installed in all empty drive slots.

CAUTION:

Mixing drive blanks from previous generations of PowerEdge servers is not supported.

Step

Press the release button, and slide the drive blank out of the drive slot.

Installation and Service Manual
Installing and removing system components

Содержание EMC PowerEdge T440























































































































































Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды

Dell EMC PowerEdge T440, Руководство пользователя

Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды