Dell EMC PowerEdge T440 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 150

background image

Option

Description

Internal SD Primary
Card

When

Redundancy

is set to

Disabled

, either one of the SDMicroSD card can be selected to present itself as mass

storage device by setting it to be primary card. By default primary SDMicroSD card is selected to be SD Card 1. If
SD Card 1 is not present, then the controller will select SD Card 2 to be the primary SDMicroSD card.

OS Watchdog
Timer

If your system stops responding, this watchdog timer aids in the recovery of your operating system. When this
option is set to

Enabled

, the operating system initializes the timer. When this option is set to

Disabled

(the

default), the timer does not have any effect on the system.

Memory Mapped
I/O above 4 GB

Enables or disables the support for the PCIe devices that need large amounts of memory. Enable this option only
for 64-bit operating systems. This option is set to

Enabled

by default.

Memory Mapped
I/O above Base

When set to

12 TB

, the system will map MMIO base to 12 TB. Enable this option for an OS that requires 44 bit

PCIe addressing. When set to

512 GB

, the system will map MMIO base to 512 GB, and reduce the maximum

support for memory to less than 512 GB. Enable this option only for the 4 GPU DGMA issue. This option is set to

56 TB

by default.

Slot Disablement

Enables or disables the available PCIe slots on your system. The slot disablement feature controls the configuration

of the PCIe cards installed in the specified slot. Slots must be disabled only when the installed peripheral card
prevents booting into the operating system or causes delays in system startup. If the slot is disabled, both the
Option ROM and UEFI drivers are disabled. Only slots that are present on the system will be available for control.

Table 28. Slot Disablement

Option

Description

Slot 1

Enables or disables or only the boot driver is disabled

for the PCIe slot 1. This option is set to

Enabled

by

default.

Slot 2

Enables or disables or only the boot driver is disabled

for the PCIe slot 2. This option is set to

Enabled

by

default.

Slot 3

Enables or disables or only the boot driver is disabled

for the PCIe slot 3. This option is set to

Enabled

by

default.

Slot 4

Enables or disables or only the boot driver is disabled

for the PCIe slot 4. This option is set to

Enabled

by

default.

Slot 5

Enables or disables or only the boot driver is disabled

for the PCIe slot 5. This option is set to

Enabled

by

default.

Slot Bifurcation

Allows

Platform Default Bifurcation

,

Auto discovery of Bifurcation

and

Manual bifurcation Control

. The default

is set to

Platform Default Bifurcation

. The slot bifurcation field is accessible when set to

Manual bifurcation

Control

and is grayed out when set to

Platform Default Bifurcation

or

Auto discovery of Bifurcation

.

Table 29. Slot Bifurcation

Option

Description

Auto Discovery Bifurcation Settings

Platform Default Bifurcation , Auto Bifurcation, and

Manual bifurcation

Slot 1 Bifurcation

x4 Bifurcation

Slot 2 Bifurcation

x4 Bifurcation

48

Installation and Service Manual
Pre-operating system management applications

«
...
46
47
48
49
50
...
»

Содержание EMC PowerEdge T440























































































































































Отзывы:

Нет отзывов

Похожие инструкции для EMC PowerEdge T440

Бренд: Fastora Страницы: 24

Бренд: 7starlake Страницы: 67

301300U - Ethernet Disk NAS Server

Бренд: LaCie Страницы: 62

System x3650 M4 BD Type 5466

Бренд: IBM Страницы: 786

x3105 - System - 4347

Бренд: IBM Страницы: 130

System x3650 Type 7979

Бренд: IBM Страницы: 194

HL-3400CN Series

Бренд: Brother Страницы: 280

Бренд: Brother Страницы: 308

2200W - NC Print Server

Бренд: Brother Страницы: 75

Бренд: Brother Страницы: 148

HL-3400CN Series

Бренд: Brother Страницы: 8

eBOX-3800 EmbedBox

Бренд: DM&P Group Страницы: 28

Бренд: Axis Страницы: 316

CHALLENGE CMN A012B

Бренд: Silicon Graphics Страницы: 40

Бренд: Lantronix Страницы: 40

Бренд: Intel Страницы: 80

Бренд: Intel Страницы: 97

Бренд: Intel Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды