Deep Sea Electronics Plc DSE5320 Скачать руководство пользователя страница 45

Страница: 45 / 66

DSE Model 5320 Automatic Mains Failure & Instrumentation System Operators Manual

Part No. 057-014 5320 OPERATING MANUAL ISSUE 5.1 18/06/2007 ADM

8.2.6 PLUG “F” 4 WAY

PIN

DESCRIPTION

Generator L1 sensing input. Connect to alternator L1 output.

Generator L2 sensing input. Connect to alternator L2 output. If using single phase only do not
connect this terminal.

Generator L3 sensing input. Connect to alternator L3 output. If using single phase only do not
connect this terminal.

Generator N sensing input. Connect to alternator N output.

8.2.7 PLUG “G” 5 WAY

PIN No

DESCRIPTION

Generator L1 current transformer connection.

Generator L2 current transformer connection. If single phase is used do not connect this pin.

Generator L3 current transformer connection. If single phase is used do not connect this pin.

Generator current transformer common connection and CT earth connection.

Not used. Do not connect to this terminal.

8.2.8 PLUG “H” 4 WAY

PIN

DESCRIPTION

Oil Pressure sensing input. Connect to resistive type oil pressure sender. Refer to connection
diagram for details.

Coolant Temperature sensing input. Connect to resistive type coolant temperature sender.
Refer to connection diagram for details.

Fuel Level sensing input. Connect to resistive type fuel level sender. Refer to connection
diagram for details.

Sender Common connection. Return feed from sender units - refer to connection diagram for
details.

NOTE:- When the module is configured for CAN operation, terminals 44 & 45 should be left

unconnected. Engine oil pressure and coolant temperature is transmitted to the 53xx controller on the

CAN link.

8.2.9 PURCHASING ADDITIONAL CONNECTOR PLUGS FROM DSE

If you require additional plugs from DSE, please contact our Sales department using the part numbers below.

5320 Terminal

Connector

Plug description

DSE Part number

1-8

BL08 8way 5.08mm spacing connector plug

007-125

9-19

BL11 11way 5.08mm spacing connector plug

007-135

20-22

BL03 3way 3.81mm spacing connector plug

007-409

23-26

BL04 4way 3.81mm spacing connector plug

007-408

27-34

BL08 8way 10.16mm spacing connector plug

007-410

35-38

BL04 4way 10.16mm spacing connector plug

007-003

39-43

BL05 5way 5.08mm spacing connector plug

007-329

44-47

BL04 4way 5.08mm spacing connector plug

007-100

CALL US TODAY

1-888-POWER-58

REQUEST A QUOTE

[email protected]

SHOP ONLINE

www.genpowerusa.com

Содержание DSE5320



































































Результаты поиска

Содержание DSE5320

Отзывы:

Бренды по названию

Популярные бренды

Deep Sea Electronics Plc DSE5320, Руководство по эксплуатации

Результаты поиска

Содержание DSE5320

Отзывы:

Бренды по названию

Популярные бренды