Deep Sea Electronics Plc DSE5320 Скачать руководство пользователя страница 38

Страница: 38 / 66

DSE Model 5320 Automatic Mains Failure & Instrumentation System Operators Manual

Part No. 057-014 5320 OPERATING MANUAL ISSUE 5.1 18/06/2007 ADM

8 ELECTRICAL

CONNECTIONS

Connections to the Module are via plug and sockets.

8.1 CONNECTION DETAILS

The following describes the connections and recommended cable sizes to the 8 plugs and sockets on the rear of
the Module. See rear panel layout

FIG 6

8.1.1 PLUG “A” 8 WAY

PIN

DESCRIPTION

CABLE

SIZE

NOTES

DC Plant Supply Input
(Negative)

2.5mm²

AWG 13

DC Plant Supply Input
(Positive)

2.5mm²

AWG 13

(Recommended Maximum Fuse 21A)

Emergency Stop Input

2.5mm²

AWG 13

Plant Supply Positive. Also supplies fuel &
start outputs.
(Recommended Maximum Fuse 32A)

Fuel relay Output

2.5mm²

AWG 13

Plant Supply Positive from pin 3. 16 Amp
rated.

Start relay Output

2.5mm²

AWG 13

Plant Supply Positive from pin 3. 16 Amp
rated.

Auxiliary Output relay 1

1.0mm²

AWG 18

Plant Supply Positive. 5 Amp rated.

Auxiliary Output relay 2

1.0mm²

AWG 18

Plant Supply Positive. 5 Amp rated.

Auxiliary Output relay 3

1.0mm²

AWG 18

Plant Supply Positive. 5 Amp rated.

NOTE:- When the module is configured for CAN operation, FUEL, START and AUXILIARY output

requirements may be different. Refer to CAN and DSE Wiring for further information.

CALL US TODAY

1-888-POWER-58

REQUEST A QUOTE

[email protected]

SHOP ONLINE

www.genpowerusa.com

Содержание DSE5320



































































Результаты поиска

Содержание DSE5320

Отзывы:

Бренды по названию

Популярные бренды

Deep Sea Electronics Plc DSE5320, Руководство по эксплуатации

Результаты поиска

Содержание DSE5320

Отзывы:

Бренды по названию

Популярные бренды