manualshive.com logo in svg

Deep Sea Electronics Plc DSE5320, Руководство по эксплуатации

Поделиться
Скачать
Deep Sea Electronics Plc DSE5320 Скачать руководство пользователя страница 29

DSE Model 5320 Automatic Mains Failure & Instrumentation System Operators Manual 

 

Part No. 057-014    5320 OPERATING MANUAL ISSUE 5.1    18/06/2007 ADM   

29 

 
6  FRONT PANEL CONFIGURATION  

 

This configuration mode allows the operator limited customising of the way the module operates.  

 

Operation 

Detail 

To enter the 

‘configuration mode’

 press both the 

INFO

 

and 

STOP

 buttons together. 

+

 

 

6.1.1  ENTERING THE CONFIGURATION EDITOR PIN NUMBER 

 

The configuration editor contains two sections.  

•

 

Main configuration editor (for ‘site adjustable’ or ‘commissioning’ parameters) 

•

 

Application editor (to allow installation engineers to make application changes).  
The ‘Application Editor’ is designed to allow the module to be configured for different applications without 
needing to re-configure the module settings. This makes it particularly suitable for applications where the 
generator would be used in a number of different roles, specifically in Rental or mobile type applications.  

 

If the module PIN number has been set, the PIN number request is then shown. The configuration cannot be 
viewed or changed until the PIN number is correctly entered.  

 

Enter either the ‘main’ PIN or the application PIN. 

 

If no PIN has been set, then skip to the next section. 

 

NOTE:- The ‘Application Editor’ must be enabled first in order to make it accessible from the 

module’s fascia. This is done by setting a PIN (number) for the module’s main front panel editor, using the 

5xxx for Windows™ PC configuration software. 

 

Deep Sea Electronics

Model 5220

O

I

+

AUTO

i

Warming 10s

L-N 240V 0A 50Hz

L-L 415V 0kW

RUNNING IN AUTO

 

 

 

 

- button 

+ button 

9

 button 

 

 

 
The configuration editor contains two sections.  

•

 

Main configuration editor (for ‘site adjustable’ or ‘commissioning’ parameters) 

•

 

Application editor (to allow installation engineers to make application changes).  
The ‘Application Editor’ is designed to allow the module to be configured for different applications without 
needing to re-configure the module settings. This makes it particularly suitable for applications where the 
generator would be used in a number of different roles, specifically in Rental or mobile type applications.  

 

CALL US TODAY 

1-888-POWER-58

REQUEST A QUOTE 

[email protected]

SHOP ONLINE 

www.genpowerusa.com

Содержание DSE5320



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды